ON-VEHICLE INSPECTION
Inspection · Vehicles built from Oct 2014
| INSPECT ENGINE COOLANT |
Remove the radiator cap.
- CAUTION:
- Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Check if there is any excessive deposits of rust or scale around the radiator cap and radiator filler hole. The coolant should be free from oil.
- HINT:
- If excessively dirty, clean the coolant passage and replace the coolant.
Install the radiator cap.
| INSPECT ENGINE OIL |
Check the oil for deterioration, water contamination, discoloring or thinning.
- Oil grade:
- 5W-30 and 10W-30:
- API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
- 15W-40 and 20W-50:
- API grade SL, SM or SN multigrade engine oil
| INSPECT BATTERY |
- NOTICE:
- If the battery is weak or if the engine is difficult to start, perform the following procedures.
Check the battery for damage and deformation. If severe damage, deformation or leakage is found, replace the battery.
Check the electrolyte level of each cell.
For maintenance-free batteries:
- If the electrolyte level is below the lower line, replace the battery.
- If the electrolyte level is above the lower line, check the battery voltage when cranking the engine.
- If the voltage is less than 9.6 V, recharge or replace the battery.
- HINT:
- Before checking battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).
- If the electrolyte level is below the lower line, replace the battery.
For non-maintenance-free batteries:
- If the electrolyte level is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte gravity.
- Standard gravity:
- 1.25 to 1.29 at 20°C (68°F)
- HINT:
- Before checking battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).
- If the electrolyte level is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte gravity.
| INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element from the air cleaner case.
Visually check that there is no dirt, clog, and damage to the air cleaner filter element.
- HINT:
- If there is any dirt or clog on the air cleaner filter element, clean it with compressed air.
- If any dirt or clog remains even after cleaning the air cleaner filter element with compressed air, replace it.
- If there is any dirt or clog on the air cleaner filter element, clean it with compressed air.
| INSPECT SPARK PLUG (for Leaded Gasoline Specification Vehicle) |
Check the electrode.

Using a megohmmeter, measure the insulation resistance.
- Insulation resistance:
- 10 MΩ or more
- HINT:
- If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:

Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.- Recommended spark plug:
Manufacture
Product
DENSO made
K20HR-U11
NGK made
LFR6C-11
Check the spark plug electrode gap.

- Maximum electrode gap for used spark plug:
- 1.3 mm (0.051 in.)
- Electrode gap for new spark plug:
- 1.1 mm (0.043 in.)
- NOTICE:
- When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Never attempt to adjust the gap of a used plug.
Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.- Air pressure:
- 588 kPa (6 kgf*cm2, 85 psi)
- Duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
| INSPECT SPARK PLUG (for Unleaded Gasoline Specification Vehicle) |
- NOTICE:
- Do not use a wire brush for cleaning.
- Do not attempt to adjust the electrode gap of a used spark plug.
- Do not use a wire brush for cleaning.
Check the electrode.

Using a megohmmeter, measure the insulation resistance.
- Insulation resistance:
- 10 MΩ or more
- HINT:
- If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method.

Quickly accelerate the engine to 4,000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage to its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.- Recommended spark plug:
Manufacture
Product
DENSO made
SK20HR-A11
Check the spark plug electrode gap.

- Maximum electrode gap for used spark plug:
- 1.3 mm (0.051 in.)
- Electrode gap for new spark plug:
- 1.0 to 1.1 mm (0.039 to 0.043 in.)
- NOTICE:
- When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.
Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.- Air pressure:
- 588 kPa (6 kgf*cm2, 85 psi)
- Duration:
- 20 seconds or less
- HINT:
- Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
| INSPECT VALVE LASH ADJUSTER NOISE |
Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the above inspection again.
- HINT:
- If any defects or problems are found during the above inspection, perform a lash adjuster inspection (Click here).
| INSPECT IGNITION TIMING |
Warm up and stop the engine.
- NOTICE:
- A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following items:
Powertrain / Engine and ECT / Data list / IGN Advance- Ignition timing:
- 5 to 15° BTDC at idle
- HINT:
- Refer to the intelligent tester operator's manual for further detail.
When not using the intelligent tester:
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No.4 cylinder.
- NOTICE:
- Use a timing light that detects the first signal.
- After checking, be sure to wrap the wire harness with tape.
- Use a timing light that detects the first signal.
Turn the ignition switch to the ON position.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

- SST
- 09843-18040
- NOTICE:
- Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
- When checking the ignition timing, the transmission should be in the neutral.
- Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
- HINT:
- After connecting terminals (TC and CG), engine rpm changes to approximately 1,000 to 1,500 rpm for 5 seconds, then returns to idle speed. This is because the ECM checks that the ISC (idle speed control system) operates properly.
- Perform the inspection of the ignition timing after engine rpm is returned to idle speed.
- After connecting terminals (TC and CG), engine rpm changes to approximately 1,000 to 1,500 rpm for 5 seconds, then returns to idle speed. This is because the ECM checks that the ISC (idle speed control system) operates properly.
Inspect the ignition timing
- Ignition timing:
- 3 to 7° BTDC at idle
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Inspect the ignition timing
- Ignition timing:
- 5 to 15° BTDC at idle
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
| INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
- NOTICE:
- A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine rpm should be stabilized.
When using the intelligent tester:
Connect the intelligent tester to the DLC3.
- HINT:
- Refer to the intelligent tester operator's manual for further details.
Start the engine and idle it.
Turn the intelligent tester main switch on.
Enter the following items:
Powertrain / Engine and ECT / Data list / Engine SPD- Idle speed:
- 600 to 700 rpm
- NOTICE:
- When checking the idle speed, the transmission should be in the neutral position.
- Switch off all accessories and air conditioning before connecting the intelligent tester.
- When checking the idle speed, the transmission should be in the neutral position.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
When not using the intelligent tester:

Install SST to terminal 9 (TAC) of DLC3, then connect a tachometer.
- SST
- 09843-18030
- NOTICE:
- Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Turn the ignition switch to the ON position.
Inspect the engine idling speed.
- Idle speed:
- 600 to 700 rpm
Turn the ignition switch off.
Disconnect the tachometer.
Remove the SST from terminal 9 (TAC).
- SST
- 09843-18030
| INSPECT ENGINE IDLE SPEED CONTROL SYSTEM |
Check the idle speed control system.

Using SST, connect terminals TC and CG of the DLC3.
- SST
- 09843-18040
Start the engine and idle it.
- NOTICE:
- Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
- Turn off all electrical systems before connecting the terminals.
- When checking ISC function, the transmission should be in the neutral position.
- Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
After connecting terminals (TC and CG), check that the engine speed changes to approximately 1,000 to 1,500 rpm for 5 seconds, and then returns to idle speed.

- HINT:
- If the result is not as specified, check the throttle body, DTC and wire harness.
| INSPECT COMPRESSION |
Warm up and stop the engine.
- NOTICE:
- A warmed up engine should have an engine coolant temperature of over 80°C (176°F), have an engine oil temperature of 60°C (140°F), and the engine speed should be stabilized.
Remove the intake air connector.
Disconnect the injector connectors.
Remove the ignition coils.
Remove the spark plugs.
Check the cylinder compression pressure.

Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
- Compression pressure:
- 1,230 kPa (12.5 kgf/cm2, 178 psi)
- Minimum pressure:
- 883 kPa (9.0 kgf/cm2, 128 psi)
- Difference between each cylinder:
- 98 kPa (1.0 kgf/cm2, 14 psi)
- NOTICE:
- Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
- Check the other cylinder's compression pressure in the same way.
- This measurement must be done as quickly as possible.
- Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
- HINT:
- If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and perform inspection again.
- If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
- If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.
- If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and perform inspection again.
Install the spark plugs.
Install the ignition coils.
Connect the injector connectors.
Install the intake air connector.
| INSPECT CO (for Leaded Gasoline Specification Vehicle) |
- HINT:
- This check is used only to determine whether or not the idle CO complies with regulations.
Initial condition:
Engine at normal operating temperature
Air cleaner installed
All pipes and hoses of the air induction system connected
All accessories switched off
All vacuum lines properly connected
EFI system wiring connectors fully seated
Ignition timing set correctly
Transmission in the neutral position
Tachometer and CO meter calibration at idle
- NOTICE:
- If a CO meter is not available, do not attempt to adjust the idle mixture. Always use a CO meter when adjusting the idle mixture. It is unnecessary to use the idle mixture screw for adjustments if the vehicle is in good condition.
Warm up the engine by driving at constant speed (approximately 50 km/h (31 mph)). Close the throttle valve for 5 minutes after the engine coolant temperature becomes stable (80 to 90°C (176 to 194°F)) and idle the engine for 5 minutes.
Insert a tester probe at least 40 cm (1.3 ft) into the tail pipe.

Wait at least 1 minute before measurement to allow the concentration to stabilize. Complete the measurement within 3 minutes.
- Idle CO concentration:
- 1.0 to 2.0%
If the CO concentration does not conform to regulations, adjust it by turning the idle mixture adjusting screw in the variable resistor with SST.

- SST
- 09243-00020
The idle mixture adjusting screw can be adjusted within an 180° angle range.

- HINT:
- If the CO concentration is within the specification, this adjustment is complete.
- If the CO concentration cannot be corrected by idle mixture adjustment, see the table below for other possible causes.
- If the CO concentration is within the specification, this adjustment is complete.
Remove the SST.
CO
Problems
Causes
High
Rough idle (black smoke from exhaust)
- Clogged air filter
- Plugged ventilation valve
- Faulty SFI system:
- Faulty fuel pressure regulator
- Clogged fuel return line
- Defective engine coolant temperature (ECT) sensor
- Faulty ECM
- Faulty injectors
- Faulty throttle position sensor
- Faulty MAF meter
- Clogged air filter
| INSPECT CO/HC (for Unleaded Gasoline Specification Vehicle) |
- HINT:
- The ECM properly controls the CO/HC concentration in the emission gas.
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tail pipe while idling.
Check the CO/HC concentration with the engine idling and/or running at 2,500 rpm.
- HINT:
- If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
- Check the heated oxygen sensor operation (Click here).
- Check the heated air fuel ratio sensor operation (Click here).
- See the table below for possible causes, then inspect the applicable causes and repair them if necessary.
- If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
CO
HC
Problems
Causes
Normal
High
Rough idle
- Faulty ignitions:
- Incorrect timing
- Fouled, shorted or improperly gapped plugs
- Incorrect valve clearance
- Leaks in intake and exhaust valves
- Leaks in cylinders
Low
High
Rough idle (Fluctuating HC reading)
- Vacuum leaks:
- PCV hoses
- Intake manifold
- Throttle body
- Brake booster line
- Lean mixture causing misfire
High
High
Rough idle (Black smoke from exhaust)
- Restricted air filter
- Plugged PCV valve
- Faulty SFI systems:
- Faulty pressure regulator
- Defective engine coolant temperature sensor
- Defective mass air flow meter
- Faulty ECM
- Faulty injectors
- Faulty throttle body
