2014-2019 Hiace · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

HINT:
Perform "Inspection After Repairs" after replacing the piston sub-assembly or piston ring (Click here).


1. INSTALL TIGHT PLUG

HINT:
If coolant leaks from a tight plug or a plug is corroded, replace it.


A097966E03
Text in Illustration 
*a
Front Side
*b
Intake Side
*c
Rear Side
*d
Exhaust Side
*e
1.0 mm (0.0394 in.)
-
-
  1. Apply adhesive to new tight plugs.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using SST, tap in the tight plug labeled A.

    SST
    09950-60010   (09951-00300)
    09950-70010   (09951-07100)

  1. Using SST, tap in the 8 tight plugs labeled B and D.

    SST
    09950-60010   (09951-00350)
    09950-70010   (09951-07100)

  1. Using SST, tap in the tight plugs labeled C.

    SST
    09950-60010   (09951-00400)
    09950-70010   (09951-07100)


2. INSTALL STUD BOLT

HINT:
If a stud bolt is deformed or its threads are damaged, replace it.


A337688E01
Text in Illustration 
*a
Front Side
*b
Lower Side
*c
Exhaust Side
*d
12 mm (0.472 in.)
*e
85 mm (3.35 in.)
*f
37 mm (1.46 in.)
*g
13 mm (0.512 in.)
*h
20 mm (0.787 in.)
*i
35 mm (1.38 in.)
-
-
  1. Using an E8 "TORX" socket wrench, install the stud bolts labeled A.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Apply adhesive to the hole for the stud bolt labeled B in the cylinder block. Install the stud bolt labeled B.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    HINT:
    When reusing a stud bolt, apply adhesive to the bolt before installing it.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Using an E7 "TORX" socket wrench, install the stud bolts labeled C.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


3. INSTALL STRAIGHT PIN

HINT:
It is not necessary to remove a straight pin unless it is being replaced.

  1. Using a plastic-faced hammer, tap in new straight pins to the cylinder block.

    G035890E05

    Text in Illustration 
    *a
    Height
    *b
    Wide
    *c
    Protrusion Height
    *d
    Rear Side

    Standard Straight Pin:
    Item
    Height
    Width
    Protrusion
    Pin A
    22 mm (0.866 in.)
    10 mm (0.394 in.)
    13 mm (0.512 in.)
    Pin B
    14 mm (0.551 in.)
    6.0 mm (0.236 in.)
    5.5 mm (0.217 in.)


4. INSTALL RING PIN

HINT:
It is not necessary to remove a ring pin unless it is being replaced.

  1. Using a plastic-faced hammer, tap in new ring pins to the cylinder block.

    A097969E05

    Text in Illustration 
    *a
    Front Side
    *b
    Lower Side
    *c
    Upper Side
    *d
    Height
    *e
    Width
    *f
    Protrusion

    Standard Ring Pin:
    Item
    Height
    Width
    Protrusion
    Pin A
    9.0 mm (0.354 in.)
    11 mm (0.433 in.)
    3.5 to 4.5 mm (0.138 to 0.177 in.)
    Pin B
    20 mm (0.787 in.)
    14 mm (0.511 in.)
    7.0 to 9.0 mm (0.276 to 0.354 in.)
    Pin C
    14 mm (0.511 in.)
    15 mm (0.591 in.)
    7.5 to 9.5 mm (0.295 to 0.374 in.)


5. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
  1. Apply adhesive to the cylinder block water drain cock sub-assembly.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A097970E03
    Install the cylinder block water drain cock sub-assembly as shown in the illustration.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *a
    Allowable Range
    *b
    Target Direction
    *c
    Upper Side
    *d
    Front

    NOTICE:
    1. Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.
    2. Do not loosen the cylinder block water drain cock sub-assembly to adjust it. If an adjustment is necessary, remove the cylinder block water drain cock sub-assembly and reinstall it.

  1. Install the water drain cock plug to the cylinder block water drain cock sub-assembly.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


6. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
  1. Using an E7 "TORX" socket wrench, install the 4 No. 1 oil nozzle sub-assemblies.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }


7. INSTALL CONNECTING ROD SMALL END BUSH

  1. A054732E13
    Align the oil holes of a new connecting rod small end bush and the connecting rod.
    Text in Illustration 
    *a
    Oil Hole

  1. A054717E05
    Using SST and a press, press in the connecting rod small end bush.
    SST
    09222-30010  

  1. A054733
    Using a pin hole grinder, hone the connecting rod small end bush to obtain the standard specified clearance (Click here) between the connecting rod small end bush and piston pin.

  1. Check that the piston pin fits at normal room temperature.

    1. Coat the piston pin with engine oil, and push it into the connecting rod with your thumb.


8. INSTALL PISTON WITH PIN SUB-ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the piston sub-assembly (Click here).

  1. Assemble the piston and connecting rod.

    1. G035729E08
      Using a screwdriver, install a new snap ring at one end of the piston pin hole.
      Text in Illustration 
      *a
      Service Hole Cutout Portion

      HINT:
      Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.

    2. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).

    3. Coat the piston pin with engine oil.

    4. A337633E01
      Align the front marks of the piston and connecting rod and push in the piston pin with your thumb.
      Text in Illustration 
      *a
      Front Mark

      HINT:
      The piston and pin are a matched set.

    5. G035729E09
      Using a screwdriver, install a new snap ring at the other end of the piston pin hole.
      Text in Illustration 
      *a
      Service Hole Cutout Portion

      HINT:
      Make sure that the end gap of the snap ring is not aligned with the service hole cutout portion of the piston.

    6. Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


9. INSTALL PISTON RING SET

HINT:
Perform "Inspection After Repairs" after replacing the piston ring (Click here).

  1. A164414E05
    Install the oil ring expander and 2 oil ring side rails by hand.
    Text in Illustration 
    *1
    Upper Oil Ring Side Rail
    *2
    Oil Ring Expander
    *3
    Lower Oil Ring Side Rail

  1. A337694E01
    Using a piston ring expander, install the 2 compression rings with the code mark as shown in the illustration.
    Text in Illustration 
    *1
    No. 2 Compression Ring
    *a
    Code Mark (2N)
    V100135
    Upward

    NOTICE:
    1. The No. 1 compression ring is reversible.
    2. Install the No. 2 compression ring with the code mark (2N) facing upward.

  1. A337634E01
    Position the piston rings so that the ring ends are as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Compression Ring
    *2
    No. 2 Compression Ring
    *3
    Oil Ring Expander
    *4
    Upper Oil Ring Side Rail
    *5
    Lower Oil Ring Side Rail
    *a
    Front Mark

    NOTICE:
    Do not align the compression ring ends.


10. INSTALL CRANKSHAFT BEARING

NOTICE:
Do not apply engine oil to the contact area or backside of the crankshaft bearing.

HINT:
The crankshaft bearing cap bolts are tightened in 2 progressive steps.

  1. Clean the main journal, and both surfaces of the crankshaft bearing.

  1. Install the upper crankshaft bearing.

    1. A101500E04
      Install the upper crankshaft bearing to the cylinder block as shown in the illustration.

      Reference (Difference in Dimension of Cylinder Block and Crankshaft Bearing):
      Item
      Specified Condition
      # 1, 5 journal
      3.83 mm (0.151 in.)
      # 3 journal
      1.74 mm (0.0685 in.)
      # 2, 4 journal
      2.75 mm (0.1083 in.)

      Text in Illustration 
      *a
      CORRECT
      *b
      INCORRECT
      *c
      Oil Groove

      NOTICE:
      1. Do not apply engine oil to the upper crankshaft bearings or their contact surfaces.
      2. Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.

  1. Install the lower crankshaft bearing.

    1. Install the lower crankshaft bearing to the crankshaft bearing cap.

    2. A101501E02
      Using a vernier caliper, measure the distance between the crankshaft bearing cap edge and lower crankshaft bearing edge.

      Dimension (A - B) or (B - A):
      0.3 mm (0.0118 in.) or less

      Reference (Dimension of (A) or (B)):
      Item
      Specified Condition
      # 1, 5 journal
      3.83 mm (0.151 in.)
      # 3 journal
      1.74 mm (0.0685 in.)
      # 2, 4 journal
      2.75 mm (0.108 in.)

      Text in Illustration 
      *1
      Lower Crankshaft Bearing
      *2
      Crankshaft Bearing Cap

      NOTICE:
      Do not apply engine oil to the crankshaft bearings or their contact surfaces.

  1. With the upper crankshaft bearing and lower crankshaft bearing installed, use a plastic-faced hammer to install the crankshaft bearing caps to the cylinder block.

    NOTICE:
    Make sure that the crankshaft bearing caps are installed in the correct positions and facing in the correct direction.

  1. A101502E04
    Using a vernier caliper, measure the amount of misalignment between the upper crankshaft bearing and lower crankshaft bearing as shown in the illustration.

    Standard misalignment:
    0.9 mm (0.0354 in.) or less

    Text in Illustration 
    *a
    Misalignment

  1. Remove the crankshaft bearing cap.

  1. Apply engine oil to the upper crankshaft thrust washers.

  1. A097960E03
    Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.
    Text in Illustration 
    *a
    Oil Groove

    NOTICE:
    Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged.


    1. A101504E04
      Install the 2 lower crankshaft thrust washers to the No. 3 crankshaft bearing cap with the grooves facing outward.
      Text in Illustration 
      *a
      Claw
      *b
      Oil Groove

      NOTICE:
      Be careful when installing the upper and lower crankshaft thrust washers as they are similar but cannot be interchanged. The lower crankshaft thrust washers have a claw as shown in the illustration.

  1. Apply engine oil to the lower crankshaft bearing.


11. INSTALL CRANKSHAFT
  1. Apply engine oil to the upper crankshaft bearing, and then place the crankshaft on the cylinder block.

  1. A101506
    Install the 5 crankshaft bearing caps to their proper locations.

  1. Install the crankshaft bearing cap bolts.

    1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

    2. Temporarily install the crankshaft bearing cap bolts.

      HINT:
      The main bearing cap bolts are tightened in 2 progressive steps.

    3. A101507E01
      Step 1:
      Uniformly tighten the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

      If any of the crankshaft bearing cap bolts does not meet the torque specification, replace the crankshaft bearing cap bolt.

    4. Mark the front of the bearing cap bolts with paint.

    5. Step 2:
      Tighten the bearing cap bolts 90° in the sequence shown in step 1.

    6. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.


12. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A087188
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.02 to 0.22 mm (0.000787 to 0.00866 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set. If necessary, replace the crankshaft.

    Thrust washer thickness:
    2.440 to 2.490 mm (0.0961 to 0.0980 in.)


13. INSTALL CONNECTING ROD BEARING

  1. A101528E04
    Align the connecting rod bearing claw with the groove of the connecting rod or connecting rod cap.
    Text in Illustration 
    *a
    Claw

  1. Install the bearings in the connecting rod and connecting rod cap.

    NOTICE:
    Clean the backside of the bearing and the bearing surface of the connecting rod.


14. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD
  1. Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.

  1. A337634E01
    Position the piston rings so that the ring ends are as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Compression Ring
    *2
    No. 2 Compression Ring
    *3
    Oil Ring Expander
    *4
    Upper Oil Ring Side Rail
    *5
    Lower Oil Ring Side Rail
    *a
    Front Mark

    NOTICE:
    Do not align the compression ring ends.

  1. A337636E01
    Using a piston ring compressor, push the numbered piston and connecting rod assembly into the correct cylinder with the front mark of the piston facing forward.
    Text in Illustration 
    *a
    Front
    *b
    Front Mark

  1. Match the numbered connecting rod cap with the correct connecting rod.

  1. A097980E07
    Check that the front mark of the connecting rod cap is facing forward.
    Text in Illustration 
    *a
    Front Mark

  1. Install the connecting rod cap bolts.

    HINT:
    The connecting rod cap bolts are tightened in 2 progressive steps.


    1. Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.

    2. G035198E01
      Step 1:
      Install and alternately tighten the bolts of the connecting rod cap in several steps.

      Torque:
      25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    3. Mark the front of each connecting rod cap bolt with paint.

    4. Step 2:
      Tighten the cap bolts 90° as shown.

    5. Check that the paint marks are now at a 90° angle to the front.

  1. Check that the crankshaft turns smoothly.


15. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A087181
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.35 mm (0.00591 to 0.0138 in.)

    Maximum thrust clearance:
    0.40 mm (0.0157 in.)

    If the thrust clearance is more than the maximum, replace the connecting rod assembly. If necessary, replace the crankshaft.


16. INSTALL INTAKE VALVE GUIDE BUSH
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard Bush Bore Diameter:
    Item
    Specified Condition
    STD
    10.285 to 10.306 mm (0.405 to 0.406 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.407 to 0.408 in.)

    If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore so that the diameter is between 10.335 and 10.356 mm (0.407 and 0.408 in.).
    If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

  1. Select a new intake valve guide bush.

    New Valve Guide Bush:
    Item
    Specified Condition
    Bush Diameter
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)
    Bush to be Used
    STD
    O/S 0.05

    HINT:
    Standard intake valve guide bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)

  1. Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head sub-assembly on wooden blocks.

  1. A101405E04
    Using SST and a hammer, tap in a new intake valve guide bush to the specified protrusion height.
    SST
    09201-01055  
    09950-70010   (09951-07100)

    Standard protrusion height:
    9.8 to 10.2 mm (0.386 to 0.402 in.)

    Text in Illustration 
    *a
    Protrusion Height

  1. A101406
    Using a sharp 5.5 mm reamer, ream the intake valve guide bush to obtain the standard clearance between the intake valve guide bush and valve stem.

    Standard oil clearance:
    0.025 to 0.060 mm (0.000984 to 0.00236 in.)


17. INSTALL EXHAUST VALVE GUIDE BUSH
  1. Using a caliper gauge, measure the bush bore diameter of the cylinder head.

    Standard Bush Bore Diameter:
    Item
    Specified Condition
    STD
    10.285 to 10.306 mm (0.405 to 0.406 in.)
    O/S 0.05
    10.335 to 10.356 mm (0.407 to 0.408 in.)

    If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore so that the diameter is between 10.335 and 10.356 mm (0.407 and 0.408 in.).
    If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head sub-assembly.

  1. Select a new exhaust valve guide bush.

    New Valve Guide Bush:
    Item
    Specified Condition
    Bush Diameter
    10.333 to 10.344 mm (0.4068 to 0.4072 in.)
    10.383 to 10.394 mm (0.4088 to 0.4092 in.)
    Bush to be Used
    STD
    O/S 0.05

    HINT:
    Standard exhaust valve guide bush length: 43.0 to 44.0 mm (1.69 to 1.73 in.)

  1. Heat the cylinder head sub-assembly to 80 to 100°C (176 to 212°F).

  1. Place the cylinder head sub-assembly on wooden blocks.

  1. A101408E04
    Using SST and a hammer, tap in a new valve guide bush to the specified protrusion height.
    SST
    09201-01055  
    09950-70010   (09951-07100)

    Standard protrusion height:
    7.6 to 8.0 mm (0.299 to 0.315 in.)

    Text in Illustration 
    *a
    Protrusion Height

  1. A101409
    Using a sharp 5.5 mm reamer, ream the exhaust valve guide bush to obtain the standard clearance between the exhaust valve guide bush and valve stem.

    Standard oil clearance:
    0.030 to 0.065 mm (0.00118 to 0.00256 in.)


18. INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:
G037442E07
It is not necessary to remove a ring pin unless it is being replaced.

  1. Remove the ring pins.

  1. Using a plastic-faced hammer, tap in a new ring pin until the pin stops.

    Standard Ring Pin:
    Item
    Height
    Width
    Protrusion Height
    Ring pin
    7 mm (0.276 in.)
    10 mm (0.394 in.)
    2.5 to 3.8 mm (0.0984 to 0.150 in.)

    Text in Illustration 
    *a
    Height
    *b
    Width
    *c
    Protrusion Height


19. INSTALL STUD BOLT

NOTICE:
If a stud bolt is deformed or its threads are damaged, replace it.


A337749E02
Text in Illustration 
*a
Cylinder Head Upper Side
*b
Intake Side
*c
Front Side
*d
Exhaust Side
*e
21 mm (0.827 in.)
*f
9 mm (0.354 in.)
*g
34 mm (1.34 in.)
*h
18 mm (0.709 in.)
*i
13 mm (0.512 in.)
*j
44 mm (1.73 in.)
*k
20 mm (0.787 in.)
*l
35 mm (1.38 in.)
*m
14 mm (0.551 in.)
*n
63 mm (2.48 in.)
*o
12 mm (0.472 in.)
-
-
  1. Using E6, E7 and E8 "TORX" socket wrenches, install the stud bolts.

    Torque:
    for stud bolt A:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
    for stud bolt B and C:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


20. INSTALL NO. 1 HEAD STRAIGHT SCREW PLUG

NOTICE:
If coolant leaks from a No. 1 head straight screw plug or a plug is corroded, replace it.

  1. Using a 10 mm hexagon wrench, install 3 new gaskets and the No. 1 head straight screw plugs.

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


21. INSTALL NO. 2 HEAD STRAIGHT SCREW PLUG

NOTICE:
If coolant leaks from the No. 2 head straight screw plug or the plug is corroded, replace it.

  1. Using a 19 mm hexagon wrench, install a new gasket and the No. 2 head straight screw plug.

    Torque:
    140 N*m{ 1428 kgf*cm , 103 ft.*lbf }


22. INSTALL OIL CONTROL VALVE FILTER
  1. Check that no foreign matter is on the mesh part of the filter.
    If foreign objects are present, clean the part thoroughly.

  1. Using an 8 mm hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


23. INSTALL VALVE SPRING SEAT
  1. Install the 16 valve spring seats to the cylinder head sub-assembly.


24. INSTALL VALVE STEM OIL SEAL

  1. A101414E06
    Apply a light coat of engine oil to new valve stem oil seals.
    Text in Illustration 
    *a
    Intake Side
    *b
    Exhaust Side
    *c
    Gray
    *d
    Black

    NOTICE:
    Pay attention when installing the intake and exhaust valve stem oil seals. Installing an intake valve stem oil seal to the exhaust side or installing an exhaust valve stem oil seal to the intake side can cause installation problems later.

    HINT:
    The intake valve stem oil seals are gray and the exhaust valve stem oil seals are black.

  1. A101415E02
    Using SST, push in the 16 valve stem oil seals to install them.
    SST
    09201-41020  
    Text in Illustration 
    *1
    Valve Stem Oil Seal

    NOTICE:
    Failure to use SST will cause the valve stem oil seal to be damaged or improperly seated.


25. INSTALL INTAKE VALVE

  1. A101416E05
    Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. A332526E01
    Install the intake valve, inner compression spring and valve spring retainer to the cylinder head.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A333831E01
    Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
    SST
    09202-70020  
    09202-00021  

  1. A333836E03
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
    Text in Illustration 
    *a
    5 mm Pin Punch

    NOTICE:
    Do not damage the valve stem tip.


26. INSTALL EXHAUST VALVE

  1. A101419E05
    Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
    Text in Illustration 
    *a
    30 mm (1.18 in.) or more

  1. A332527E01
    Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.
    Text in Illustration 
    *a
    Narrow
    *b
    Wide

    NOTICE:
    Install the same parts in the same combination to the original locations.

  1. A333832E01
    Using SST and wooden blocks, compress the inner compression spring and install the 2 valve spring retainer locks.
    SST
    09202-70020  
    09202-00021  

  1. A333837E04
    Using a 5 mm pin punch and plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
    Text in Illustration 
    *a
    5 mm Pin Punch

    NOTICE:
    Do not damage the valve stem tip.


27. INSTALL OIL FILTER BRACKET SUB-ASSEMBLY
  1. Install 2 new gaskets and 2 straight screw plugs to the oil filter bracket sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

  1. Install 2 new O-rings, gasket and oil filter bracket with the union bolt and nut.

    Torque:
    for union bolt:
    69 N*m{ 699 kgf*cm , 51 ft.*lbf }
    for nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Apply a light coat of engine oil to the new O-rings.


28. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

  1. A268595E01
    Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element in the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

  1. A309157E01
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Cap
    *2
    O-Ring
    *3
    Oil Filter Bracket
    *a
    No Gap


29. INSTALL REAR CRANKSHAFT OIL SEAL

  1. A103252E03
    Place the rear engine oil seal retainer on wooden blocks.
    Text in Illustration 
    *a
    Wooden Block

  1. Using SST, tap in a new rear crankshaft oil seal until its surface is flush with the rear engine oil seal retainer edge.

    SST
    09223-15030  
    09950-70010   (09951-07150)

    NOTICE:
    Do not tap the rear crankshaft oil seal at an angle.

  1. Apply a light coat of MP grease to the lip of a new rear crankshaft oil seal.

    NOTICE:
    1. Do not allow foreign matter to contact the lip of the rear crankshaft oil seal.
    2. Do not allow MP grease to contact the dust seal.


30. INSTALL REAR ENGINE OIL SEAL RETAINER

  1. A097914E05
    Apply seal packing in a continuous bead as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Standard seal width:
    2.5 to 3.5 mm (0.0984 to 0.138 in.)

    Text in Illustration 
    *a
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the crankcase within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 4 hours after installing.

  1. Install the rear engine oil seal retainer with the 6 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    Wipe off any seal packing that has leaked out within 10 minutes.


31. INSTALL CYLINDER HEAD GASKET
  1. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head sub-assembly or cylinder block.

  1. A337677E01
    Apply seal packing to a new cylinder head gasket as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207 B or equivalent.

    Text in Illustration 
    *1
    Cylinder Head Gasket
    *a
    7.0 to 9.0 mm (0.276 to 0.354 in.)
    *b
    5.0 to 7.0 mm (0.197 to 0.276 in.)
    *c
    3.0 to 5.0 mm (0.118 to 0.197 in.)
    *d
    166.25 mm (6.55 in.)
    *e
    62.25 mm (2.46 in.)
    *f
    Side View
    *g
    View A

    NOTICE:
    1. Be sure to clean and degrease the contact surfaces.
    2. Apply seal packing to the bead on the cylinder head gasket.
    3. Install the cylinder head gasket within 3 minutes and tighten the cylinder head set bolts within 15 minutes after applying seal packing.

  1. A097916E07
    Place the gasket on the cylinder block surface with the lot No. stamp facing upward.
    Text in Illustration 
    *a
    Lot No.
    V100135
    Engine Front

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Make sure that the cylinder head gasket is installed in the correct direction.


32. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
  1. Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly (Click here).
  2. The cylinder head set bolts are tightened in 3 successive steps.

  1. Place the cylinder head sub-assembly on the cylinder block.

    NOTICE:
    1. Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.
    2. Place the cylinder head sub-assembly on the cylinder block gently so as not to damage the gasket with the bottom part of the head.

  1. Install the plate washers to the cylinder head set bolts.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.

  1. A101319E05
    Step 1:
    Using several steps, install and uniformly tighten the 10 cylinder head set bolts with plate washers in the sequence shown in the illustration.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. Mark the front of each cylinder head set bolt head with paint.

  1. Step 2:
    Tighten the cylinder head set bolts 90° in the sequence shown in step 1.

  1. Step 3:
    Tighten the cylinder head set bolts another 90° in the sequence shown in step 1.

  1. Check that the paint marks are now at a 180° angle to the front.


33. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly (Click here).

  1. A344602E01
    Using SST, grip the hexagonal portion, and then secure the SST and No. 2 camshaft in a vise as shown in the illustration.
    SST
    09212-31010  
    Text in Illustration 
    *a
    Hexagonal Portion

    NOTICE:
    1. Do not damage the No. 2 camshaft.
    2. Never grip areas other than the hexagonal portion, as this may cause damage.

  1. A336440E01
    Align and attach the straight pin of the No. 2 camshaft with the straight pin hole of the camshaft timing exhaust gear assembly.
    Text in Illustration 
    *a
    Straight Pin Hole
    *b
    Straight Pin

  1. A336442E01
    Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.
    Text in Illustration 
    *1
    Camshaft Timing Exhaust Gear Assembly
    *a
    INCORRECT
    *b
    CORRECT
    *c
    Clearance
    *d
    Camshaft Flange
    *e
    No Clearance

    NOTICE:
    Be sure not to remove the other 4 bolts. If removing the bolts, exchange the camshaft timing exhaust gear assembly.

  1. Fix the camshaft timing exhaust gear assembly with the flange bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }


34. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:
Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly (Click here).

  1. A344602E01
    Using SST, grip the hexagonal portion, and then secure the SST and camshaft in a vise as shown in the illustration.
    SST
    09212-31010  
    Text in Illustration 
    *a
    Hexagonal Portion

    NOTICE:
    1. Do not damage the camshaft.
    2. Never grip areas other than the hexagonal portion, as this may cause damage.

  1. A336438E01
    Align the straight pin hole and straight pin and install the camshaft timing gear assembly to the camshaft.
    Text in Illustration 
    *a
    Straight Pin
    *b
    Straight Pin Hole

  1. Lightly press the gear against the camshaft and turn the gear. Push further at the position where the straight pin enters the straight pin hole.

    NOTICE:
    Be sure not to turn the camshaft timing gear assembly in the retard direction (the right angle).

  1. A336441E01
    Check that there is no clearance between the camshaft timing gear assembly and the flange of the camshaft.
    Text in Illustration 
    *1
    Camshaft Timing Gear Assembly
    *a
    INCORRECT
    *b
    CORRECT
    *c
    Clearance
    *d
    Camshaft Flange
    *e
    No Clearance

    NOTICE:
    1. Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being removed. If the camshaft is not kept level, the portion of the cylinder head receiving the shaft thrust may crack or be damaged, causing the camshaft to seize or break.
    2. Be sure not to remove the other 3 bolts. If removing the bolts, exchange the camshaft timing gear assembly.

  1. With the camshaft timing gear assembly fixed in place, install the flange bolt.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. Check that the camshaft timing gear assembly can move in the retard direction (the right angle), and is locked at the most retarded position.


35. INSTALL VALVE LASH ADJUSTER ASSEMBLY
  1. Inspect each valve lash adjuster assembly before installing it (Click here).

  1. Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

    NOTICE:
    Install each valve lash adjuster assembly to the same place it was removed from.


36. INSTALL VALVE STEM CAP
  1. Apply a light coat of engine oil to the valve stem ends.

  1. Install the 16 valve stem caps to the cylinder head sub-assembly.

    NOTICE:
    Do not drop the valve stem caps into the cylinder head sub-assembly.


37. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply clean engine oil to the valve lash adjuster assembly tips and valve stem cap surfaces.

  1. A336446E01
    Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap
    *a
    INCORRECT
    *b
    CORRECT

    NOTICE:
    Install the valve stem cap, valve lash adjuster assembly and No. 1 valve rocker arm sub-assembly to the same places they were removed from.


38. INSTALL CAMSHAFTS

HINT:
Perform "Inspection After Repairs" after replacing the camshaft or No. 2 camshaft (Click here).

  1. A336456E01
    Apply clean engine oil to the camshaft cams and cylinder head journals.

  1. Position the camshaft and No. 2 camshaft as shown in the illustration.

  1. A336446E01
    Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
    Text in Illustration 
    *1
    No. 1 Valve Rocker Arm Sub-assembly
    *2
    Valve Lash Adjuster Assembly
    *3
    Valve Stem Cap
    *a
    INCORRECT
    *b
    CORRECT


39. INSTALL CAMSHAFT BEARING CAP

  1. A336457
    Temporarily install the No. 1 camshaft bearing cap.

  1. Confirm the location for each No. 2 camshaft bearing cap and install each one to the proper location.

  1. Uniformly temporarily install the 20 bolts while keeping the camshaft level.

  1. A336452E01
    Tighten the 20 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 158 kgf*cm , 11 ft.*lbf }


40. INSTALL OIL JET
  1. Install a new gasket and oil jet with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


41. INSTALL CRANKSHAFT PULLEY SET KEY
  1. Install the 2 crankshaft pulley set keys to the crankshaft.


42. INSTALL CRANK POSITION SENSOR ROTOR

  1. A097919E06
    Install the crankshaft position sensor rotor with the front mark facing forward.
    Text in Illustration 
    *1
    Crankshaft Pulley Set Key
    *a
    Front Mark
    *b
    Key Groove


43. INSTALL NO. 1 CHAIN VIBRATION DAMPER
  1. Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


44. INSTALL CHAIN SUB-ASSEMBLY

  1. A337689E01
    As shown in the illustration, install the chain sub-assembly to the camshaft timing exhaust gear assembly and camshaft timing gear assembly with the mark plates aligned with the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Key
    *a
    Timing Mark
    *b
    Mark Plate (Yellow)
    *c
    Mark Plate (Pink)
    *d
    Approximately 13°
    *e
    Approximately 30°

    HINT:
    1. The camshaft mark plate is yellow.
    2. The crankshaft mark plate is pink.

  1. A340607
    Use a rope to secure the chain sub-assembly of the crankshaft timing gear or sprocket. Tie the rope near the crankshaft timing gear or sprocket.

    NOTICE:
    After the No. 1 chain tensioner assembly has been installed, the rope must be removed.

    HINT:
    The rope is used to prevent the chain sub-assembly from jumping a tooth.


45. INSTALL CHAIN TENSIONER SLIPPER
  1. Install the chain tensioner slipper with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


46. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
  1. Install a new gasket and the No. 1 chain tensioner assembly with the bolt and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Remove the hexagon wrench after installing the timing chain guide.


47. INSTALL TIMING CHAIN GUIDE

  1. A336451E01
    Install a new O-ring and the timing chain guide with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    Text in Illustration 
    *1
    O-ring


48. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

  1. Check that the No. 1 cylinder is set to TDC/compression.

    1. A336450E03
      Rotate the crankshaft two full rotations, and then check that all timing marks are in the position shown in the illustration.
      If the timing marks do not match, set the chain sub-assembly again.
      Text in Illustration 
      *1
      Key
      *a
      Timing Mark
      *b
      Approximately 13°
      *c
      Approximately 30°


49. INSTALL CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY
  1. Install a new No. 2 camshaft bearing cap oil hole gasket and 3 new No. 3 camshaft bearing cap oil hole gaskets to the camshaft bearing cap.

  1. Install the cylinder head cover connector sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


50. INSTALL TIMING CHAIN CASE OIL SEAL

  1. A336770E01
    Using SST and a hammer, tap in a new timing chain case oil seal until its surface is flush with the edge of the timing chain or belt cover sub-assembly.
    SST
    09223-75010  
    09950-70010   (09951-07100)

    NOTICE:
    1. Keep the lip free from foreign matter.
    2. Do not tap the timing chain case oil seal at an angle.

  1. Apply MP grease to the lip of the timing chain case oil seal.


51. INSTALL ENGINE WATER PUMP ASSEMBLY
  1. Install a new gasket and the engine water pump assembly with the 8 bolts.

    Torque:
    8.9 N*m{ 91 kgf*cm , 79 in.*lbf }


52. INSTALL TIMING CHAIN OR BELT COVER SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the timing chain or belt cover sub-assembly, cylinder head sub-assembly and cylinder block sub-assembly.

  1. Install 3 new O-rings to the timing chain or belt cover sub-assembly.

  1. A336772
    Align the width of the joint portion of the oil pump drive rotor and the crankshaft timing gear, and then install the timing chain or belt cover sub-assembly.

  1. Apply seal packing as shown in the illustration.

    A336771E01

    Text in Illustration 
    *1
    Cylinder Head Sub-assembly
    *2
    Cylinder Block Sub-assembly
    *a
    2.0 mm (0.0787 in.)
    *b
    2.5 mm (0.0984 in.)
    *c
    3.0 mm (0.118 in.)
    *d
    5.0 mm (0.197 in.)
    *e
    6.0 mm (0.236 in.)
    *f
    7.0 mm (0.276 in.)
    *g
    8.0 mm (0.315 in.) or more
    *h
    20 mm (0.787 in.)
    *i
    42 mm (1.65 in.)
    *j
    43 mm (1.69 in.)
    *k
    56.5 mm (2.22 in.)
    *l
    2.5 to 4.0 mm (0.0984 to 0.157 in.)
    *m
    5.0 to 6.0 mm (0.197 to 0.236 in.)
    *n
    9.0 to 13 mm (0.354 to 0.512 in.)
    *o
    10 to 14 mm (0.394 to 0.551 in.)
    *p
    12 to 16 mm (0.472 to 0.630 in.)
    *q
    Seal Packing
    -
    -

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the timing chain or belt cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not add the engine oil for at least 4 hours after the installation.
    4. Do not start the engine for at least 4 hours after the installation.

  1. Install the timing chain or belt cover sub-assembly with the 16 bolts and nut, and tighten the 16 bolts and nut in the sequence shown in the illustration.

    A336802E01

    Text in Illustration 
    *a
    Types of nut and bolt
    *b
    Tightening Order
    V100135
    Bolt
    V100136
    Nut

    Torque:
    for Bolt A:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }
    for Bolt B and Nut:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }
    for Bolt C:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    for Bolt D:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Bolt Length:
    Item
    Length
    Thread Diameter
    Bolt A
    75 mm (2.95 in.)
    10 mm (0.394 in.)
    Bolt B
    75 mm (2.95 in.)
    8.0 mm (0.315 in.)
    Bolt C
    40 mm (1.57 in.)
    8.0 mm (0.315 in.)
    Bolt D
    90 mm (3.54 in.)
    8.0 mm (0.315 in.)

  1. A336774
    Remove the seal packing from the 2 bolt holes for the No. 1 compressor mounting bracket.

    NOTICE:
    Do not use any cleaners to remove the seal packing.


53. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A336470E01
    Install the oil strainer sub-assembly with the 6 bolts, and tighten the 6 bolts in the sequence shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


54. INSTALL OIL PAN SUB-ASSEMBLY

  1. Install the stud bolt.

    1. A337637E01
      Using an E6 "torx" socket wrench, install the stud bolts.
      Text in Illustration 
      *a
      9.0 mm (0.354 in.)
      *b
      19.0 mm (0.748 in.)

      Torque:
      3.0 N*m{ 31 kgf*cm , 27 in.*lbf }

  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

  1. A341261E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    2.0 to 3.0 mm (0.0787 to 0.118 in.)

    Text in Illustration 
    *a
    8.0 mm (0.315 in.)
    *b
    6.5 mm (0.256 in.)
    *c
    Seal Packing

    NOTICE:
    1. Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Do not add the engine oil for at least 4 hours after the installation.
    3. Do not start the engine for at least 4 hours after the installation.

  1. Install a new gasket to the oil strainer sub-assembly.

  1. A337667E03
    Install the oil pan sub-assembly with the 16 bolts and 2 nuts, and tighten the 16 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    Bolt Length:
    Item
    Length
    Bolt A
    20 mm (0.787 in.)
    Bolt B
    40 mm (1.57 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B
    V100137
    Nut


55. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
  1. Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the oil pan sub-assembly and No. 2 oil pan sub-assembly.

  1. G037317E06
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    3.0 to 4.0 mm (0.118 to 0.157 in.)

    Text in Illustration 
    *a
    6.0 mm (0.236 in.)
    *b
    Seal Packing

    NOTICE:
    1. Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    2. Do not add the engine oil for at least 4 hours after the installation.
    3. Do not start the engine for at least 4 hours after the installation.

  1. A336798E01
    Install the No. 2 oil pan sub-assembly with the 18 bolts and 2 nuts, and tighten the 18 bolts and 2 nuts in the sequence shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    38 N*m{ 382 kgf*cm , 28 ft.*lbf }


56. INSTALL CRANKSHAFT PULLEY
  1. Align the key groove of the crankshaft pulley with the crankshaft pulley set key and install the crankshaft pulley.

  1. A101367E02
    Using SST, hold the crankshaft pulley in place and tighten a new crankshaft pulley set bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

    Torque:
    260 N*m{ 2651 kgf*cm , 192 ft.*lbf }

    NOTICE:
    Do not reuse the crankshaft pulley set bolt.


57. INSTALL NO. 1 VENTILATION CONNECTOR
  1. Install the No. 1 ventilation connector to the cylinder head cover sub-assembly with the 2 bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }


58. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

59. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A337845
    for Intake Side:

    1. Apply a light coat of engine oil to the a new O-ring, and install it to the camshaft timing oil control valve assembly.

      NOTICE:
      Do not damage the O-ring when installing.

      HINT:
      An O-ring is already installed in a new camshaft timing oil control valve assembly. So, the O-ring only needs to be coated with engine oil when the assembly is replaced with a new one.

    2. Install the camshaft timing oil control valve assembly to the cylinder head sub-assembly with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      NOTICE:
      1. Replace with a new part if it is dropped or if it receives a strong impact.
      2. Make sure that the O-ring is not cracked or jammed when installing.

    3. Connect the camshaft timing oil control valve connector.

  1. for Exhaust Side:

    1. Apply a light coat of engine oil to the a new O-ring, and install it to the camshaft timing oil control valve assembly.

      NOTICE:
      Do not damage the O-ring when installing.

      HINT:
      An O-ring is already installed in a new camshaft timing oil control valve assembly. So, the O-ring only needs to be coated with engine oil when the assembly is replaced with a new one.

    2. Install the camshaft timing oil control valve assembly to the cylinder head cover sub-assembly with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      NOTICE:
      1. Replace with a new part if it is dropped or if it receives a strong impact.
      2. Make sure that the O-ring is not cracked or jammed when installing.

    3. Connect the camshaft timing oil control valve connector.


60. INSTALL CRANKSHAFT POSITION SENSOR
  1. Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.

  1. Install the crankshaft position sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. When reusing the crankshaft position sensor, inspect the O-ring.
    2. Make sure that the O-ring is not cracked or jammed when installing the crankshaft position sensor.

  1. Connect the crankshaft position sensor connector and attach the 2 wire harness clamps.


61. INSTALL CAMSHAFT POSITION SENSOR
  1. for Intake Side:

    1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    2. Install the camshaft position sensor with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      NOTICE:
      1. When reusing the camshaft position sensor, inspect the O-ring.
      2. Make sure that the O-ring is not cracked or jammed when installing the camshaft position sensor.

    3. Connect the camshaft position sensor connector.

  1. for Exhaust Side:

    1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

    2. Install the camshaft position sensor with the bolt.

      Torque:
      9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

      NOTICE:
      1. When reusing the camshaft position sensor, inspect the O-ring.
      2. Make sure that the O-ring is not cracked or jammed when installing the camshaft position sensor.

    3. Connect the camshaft position sensor connector.


62. INSTALL PCV VALVE SUB-ASSEMBLY

  1. A253711E01
    Apply a light coat of engine oil to the O-ring.
    Text in Illustration 
    *1
    O-Ring

  1. Install the PCV valve sub-assembly.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    HINT:
    When reusing the PCV valve sub-assembly, inspect the O-ring.

    If the O-ring has scratches or cuts, replace the PCV valve sub-assembly.

  1. Connect the PCV hose to the PCV valve sub-assembly, and slide the clamp to secure the hose.


63. INSTALL OIL FILLER CAP SUB-ASSEMBLY
← REASSEMBLY (Oct 2014 – Dec 2014)ON-VEHICLE INSPECTION (from Oct 2014) →