REASSEMBLY
Removal / installation · Vehicles built Oct 2014 – Dec 2016
Versions by build date: Oct 2014 – Dec 2016 from Jan 2017
| 1.
INSTALL NO.2 SEATBACK SPRING ASSEMBLY LH |
|
| 2.
INSTALL NO.2 SEATBACK SPRING ASSEMBLY RH |
|
| 3.
INSTALL NO.2 SEATBACK PAD |
|
| 4.
INSTALL NO.2 SEATBACK COVER SUB-ASSEMBLY |
 |
- Using hog ring pliers, install the No.2 seatback cover sub-assembly with 2 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- HINT:
- Use the same procedures for the RH side and LH side.
| 5.
INSTALL NO.2 SEATBACK COVER SUB-ASSEMBLY WITH PAD |
|
| 6.
INSTALL REAR SEAT HEADREST SUPPORT LH |
|
| 7.
INSTALL REAR SEAT HEADREST SUPPORT RH |
|
| 8.
INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH (w/ Assist Grip) |
|
| 9.
INSTALL ASSIST GRIP (w/ Assist Grip) |
|
| 10.
INSTALL REAR SEATBACK SHIELD RH |
|
| 11.
INSTALL REAR SEATBACK SHIELD LH |
|
| 12.
INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 LH |
|
| 13.
INSTALL REAR SEAT CUSHION SHIELD INNER NO.1 RH |
|
| 14.
INSTALL REAR SEAT HEADREST ASSEMBLY |
|
| 15.
INSTALL REAR SEAT BELT ASSEMBLY INNER (w/ Seat Belt)
|
 |
- Install the rear seat belt assembly inner with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 16.
INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY (w/ Seat Belt)
|
 |
- Install the rear seat lap type belt assembly with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 17.
INSTALL NO.2 SEAT LEG SUB-ASSEMBLY |
 |
- w/o Seat Belt:
Install the No.2 seat leg sub-assembly with the 8 bolts.
-
Torque:
- 41 N*m{
418 kgf*cm
, 30 ft.*lbf
}
w/ Rear seat lap type belt assembly:
Install the No.2 seat leg sub-assembly with the 8 bolts.
-
Torque:
- 41 N*m{
418 kgf*cm
, 30 ft.*lbf
}
- w/ Rear seat 3-point type belt assembly:
Install the No.2 seat leg sub-assembly with the 7 bolts.
-
Torque:
- 41 N*m{
418 kgf*cm
, 30 ft.*lbf
}
| 18.
INSTALL REAR SEAT 3-POINT TYPE BELT ASSEMBLY (w/ Rear Seat 3-Point Type Belt Assembly)
|
 |
- Install the rear seat 3 point type belt assembly with the 2 bolts.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
Install the 4 screws.
| 19.
INSTALL NO.2 SEAT CUSHION PAD |
|
| 20.
INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY |
 |
- Using hog ring pliers, install the No.2 seat cushion cover sub-assembly with 16 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
- Using hog ring pliers, install the 5 new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.
| 21.
INSTALL NO.2 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD |
|
| 22.
INSTALL SEAT LAP TYPE BELT ASSEMBLY NO.1 (w/ Seat Lsp Type Belt Assembly No.1)
|
 |
- Install the seat lap type belt assembly No.1 with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 23.
INSTALL REAR SEAT BELT ASSEMBLY INNER (w/ Seat Belt)
|
 |
- Install the rear seat belt assembly inner with the bolt.
-
Torque:
- 42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
| 24.
INSTALL REAR SEAT LEG SIDE COVER NO.5 |
|
| 25.
INSTALL REAR SEAT LEG SIDE COVER NO.4 |
|
| 26.
INSTALL RECLINING ADJUSTER COVER LH |
|
| 27.
INSTALL RECLINING ADJUSTER COVER RH |
|
| 28.
INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 LH |
|
| 29.
INSTALL RECLINING ADJUSTER RELEASE HANDLE NO.2 RH |
|