2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


1. INSPECT CYLINDER HEAD SET BOLT

  1. A057442E02
    Using vernier calipers, measure the minimum outer diameter of the compressed thread at the measuring point.

    Standard outer diameter:
    11.80 to 12.00 mm (0.4646 to 0.4724 in.)

    Minimum outer diameter:
    11.60 mm (0.4567 in.)

    If the outer diameter is less than the minimum, replace the bolt.


2. INSTALL CYLINDER HEAD GASKET

  1. A056837E02
    Check piston protrusion for each cylinder.

    1. Clean the cylinder block with solvent.

    2. Set the piston of the cylinder to be measured to slightly before TDC.

    3. Place a dial indicator on the cylinder block, and set the measuring tip as shown in the illustration.

    4. Set the dial indicator at 0 mm (0 in.).

      HINT:
      1. Use a dial indicator measuring tip as shown in the illustration.
      2. Make sure that the measuring tip is square to the cylinder block gasket surface and piston head when taking the measurements.

    5. A058740E01
      Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.

    6. A056896E02
      Measure the protrusion of each cylinder at 2 places as shown in the illustration, making a total of 8 measurements.

    7. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

      Protrusion:
      0.68 to 0.97 mm (0.00268 to 0.0382 in.)

      HINT:
      If the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall it.

  1. A057643E02
    Select a new cylinder head gasket.

    HINT:
    There are 3 sizes of new cylinder head gaskets, marked "B", "D" or "F" accordingly.
    New installed cylinder head gasket thickness: 
    Mark B
    1.40 to1.50 mm (0.0551 to 0.0591 in.)
    Mark D
    1.50 to 1.60 mm (0.0591 to 0.0630 in.)
    Mark F
    1.60 to 1.70 mm (0.0630 to 0.0669 in.)


    1. Select the largest piston protrusion value from the measurements made, then select a new appropriate gasket according to the table below.

      Piston protrusion mm (in.)
      Gasket size
      0.68 to 0.77 (0.0268 to 0.0303)
      Use B
      0.78 to 0.87 (0.0307 to 0.0343)
      Use D
      0.88 to 0.97 (0.0346 to 0.0382)
      Use F

  1. A056909E01
    Place a new cylinder head gasket in position on the cylinder block.

    NOTICE:
    Be careful of the installation direction.


3. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
Set the No.1 cylinder to 90° BTDC/compression to avoid interference with the piston top and valve head.

  1. A058738E01
    Using the crankshaft pulley bolt, turn the crankshaft 90° counterclockwise, and align the timing mark of the crankshaft timing pulley with the protrusion of the timing belt case.

  1. Place the cylinder head in position on the cylinder head gasket.

  1. A058739E01
    Install cylinder head bolts.

    HINT:
    1. The cylinder head bolts are tightened in 3 progressive steps (steps (2), (4) and (5))
    2. If any bolt is broken or deformed, replace it.


    1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

    2. Install and uniformly tighten the 18 cylinder head bolts, in several steps, in the sequence shown.

      Torque:
      78 N*m{ 800 kgf*cm , 58 ft.*lbf }

      HINT:
      Each bolt length is indicated below.
      Bolt length:
      107 mm (4.21 in.) for A
      127 mm (5.00 in.) for B

      If any one of the cylinder head bolts does not meet the torque specification, replace the cylinder head bolt.

    3. A056902E02
      Mark the front of the cylinder head bolt with paint.

    4. Retighten the cylinder head bolts 90° in the numerical order shown.

    5. Retighten the cylinder head bolts by an additional 90°.

    6. Check that the painted mark is now facing rearward.


4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A056814E02
    Remove the any oil packing (FIPG) material.

  1. Apply seal packing to the cylinder head as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

  1. Install the gasket to the cylinder head cover.

  1. Install the cylinder head cover with the 9 bolts and nut. Uniformly tighten the bolts and nuts in several steps.

    Torque:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

  1. Connect the ventilation hose.


5. INSTALL GLOW PLUG NO.1 CONNECTOR

Torque:
1.0 N*m{ 10 kgf*cm , 9 in.*lbf }


6. INSTALL INJECTION PIPE SET
  1. Connect the 2 lower clamps on the intake manifold.

  1. Install the 4 injection pipes.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

  1. Secure the injection pipes with the 2 upper pipe clamps and 2 nuts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }


7. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRON NO.1 (for Long Wheelbase)
  1. Install a new gasket and exhaust pipe sub-assembly front No.1 with the 3 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Tighten the clamp bolt, and install the exhaust pipe support bracket No.1 to the exhaust pipe sub-assembly front No.1.


8. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRON NO.1
  1. Install a new gasket and exhaust pipe sub-assembly front No.1 with the 3 bolts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }

  1. Tighten the clamp bolt, install the exhaust pipe support bracket No.1 to the exhaust pipe sub-assembly front No.1.


9. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.2 (for Long Wheelbase)

  1. A077857
    Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E05
    Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the outer face.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly tail side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1.


10. INSTALL EXHAUST PIPE SUB-ASSEMBLY FRONT NO.2 (for Super Long Wheelbase)

  1. A077857
    Inspect the compression spring.

    1. Using vernier calipers, measure the free length of the compression springs.

      Minimum length:
      40.5 mm (1.594 in.)

      HINT:
      If the free length is less than the minimum, replace the compression spring.

  1. A102062E05
    Install the gasket.

    1. Fully insert a new gasket to the exhaust pipe sub-assembly front No.1 by hand.

    2. Using a wooden block, uniformly strike the gasket so that the gasket and exhaust pipe sub-assembly front No.1 are properly fit.

      NOTICE:
      1. Be careful with the installation direction of the gasket.
      2. Do not damage the gasket.
      3. Do not reuse the gasket.
      4. To ensure a proper seal, do not use the exhaust pipe sub-assembly front No.2 to force the gasket onto the exhaust pipe sub-assembly front No.1.

  1. Connect the exhaust pipe support, and install a new gasket and the exhaust pipe sub-assembly front No.2 with the 4 bolts, 2 nuts, and 2 compression springs.

    Torque:
    Exhaust pipe sub-assembly front No.1 side:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Exhaust pipe assembly center side:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    After installation, check that the clearance is almost same at any point between the flanges of the exhaust pipe sub-assembly front No.2 and exhaust pipe sub-assembly front No.1 .


11. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.1

  1. A058726E01
    Install the heat insulator with the 3 bolts.

    Torque:
    Bolt (A):
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }
    Bolt (B):
    19 N*m{ 195 kgf*cm , 14 ft.*lbf }


12. INSTALL VENTURI ASSEMBLY
  1. Install a new gasket and venturi.

  1. A111053E01
    Connect the throttle control motor connector.

  1. A111052E01
    Connect the throttle open switch connector.


13. INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

  1. A111051
    Install a new gasket and intake air connector with the bolt and 3 nuts.

    Torque:
    bolt:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Connect the turbo pressure sensor connector.

  1. Connect the ventilation hose.


14. CONNECT AIR CLEANER HOSE NO.2
  1. Install the air cleaner hose No.2 with the clamp.


15. INSTALL TIMING BELT
(Click here)

16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

17. BLEED AIR FROM FUEL SYSTEM

  1. A114068E01
    Using the hand pump, bleed air from the fuel system until pumping becomes difficult.


18. ADD ENGINE COOLANT
  1. Fill the radiator reservoir assembly with coolant to the top of the inlet.

    Standard Capacity:
    Item
    Specified Condition
    w/o Heater
    12.3 liters (13.0 US qts, 10.8 Imp. qts)
    w/ Front Heater
    13.3 liters (14.1 US qts, 11.7 Imp. qts)
    w/ Front and Rear Heaters
    15.3 liters (16.2 US qts, 13.5 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. Use of improper coolants may damage the engine cooling system.
    2. Use only Toyota Super Long Life Coolant or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A142533
    Add coolant up to the B line mark in the radiator reservoir assembly and install the reservoir cap.

  1. Warm up the engine until the thermostat opens.

    1. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. A142532
    After the engine cools down, check that the coolant level is between the LOW and FULL level marks.


19. CHECK FOR ENGINE COOLANT LEAKS

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester to the radiator.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator or water pump for leaks. If no external leaks are found, check the heater core, cylinder block, and cylinder head.


20. CHECK FOR FUEL LEAKS
  1. Check that there are no fuel leaks anywhere on the fuel system after doing maintenance.

    HINT:
    When checking for fuel leaks, make sure that there is pressure in the fuel line.


21. CHECK FOR EXHAUST GAS LEAKS

22. CHECK IDLE SPEED
  1. Warm up the engine.

  1. When using an intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      Idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. A052006E02
    When not using an intelligent tester:

    1. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18040  

    2. Check the idle speed.

      Idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      NOTICE:
      Switch off all accessories.


23. INSPECT MAXIMUM ENGINE SPEED
  1. Start the engine.

  1. Depress the accelerator pedal all the way.

  1. Check the maximum speed.

    Maximum speed:
    4,850 to 4,950 rpm


24. PERFORM INITIALIZATION
(Click here)
← INSTALLATION (Jan 2015 – Dec 2016)COMPONENTS (from Oct 2014) →