2014-2019 Hiace · Service Manual INTRODUCTION

INITIALIZATION

Troubleshooting · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017


PROCEDURES NECESSARY WHEN CABLE IS DISCONNECTED/RECONNECTED TO BATTERY TERMINAL
Procedures Necessary when Cable is Disconnected/Reconnected to Battery Terminal 
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See page
Power window regulator motor initialization
Power Window Control System
Click here
Reset slide door close position
Power Slide Door System
Click here

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
Procedures Necessary when ECU or Other Parts are Replaced 
Replacement Part
Necessary Procedure
Effect or Inoperative Function when Necessary Procedure is not Performed
See Page
for 1KD-FTV:
  1. ECM
  1. Learning values save
  2. Learning values write
Engine starting
Click here (w/ DPF)
Click here(w/o DPF)
for 1KD-FTV:
  1. Injector assembly
  1. Input injector compensation code registration
  2. Pilot quantity learning
Engine starting
for 1KD-FTV:
  1. Engine assembly
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
Clear crank time compensation data
Engine starting
Click here (w/ DPF)
Click here (w/o DPF)
for 1KD-FTV:
  1. Crankshaft position sensor plate
Clear crank time compensation data
Engine starting
Click here (w/ DPF)
Click here (w/o DPF)
for 1KD-FTV:
  1. Fuel supply pump assembly
Supply pump initialization
Engine startability
for 1KD-FTV:
  1. Air fuel ratio sensor
Clear A/F sensor compensation data
EGR volume is affected
for 1KD-FTV, w/ DPF:
  1. DPF catalyst
Clear DPF thermal deterioration data
Even if catalytic converter is replaced with new one, catalyst record of DPF thermal deterioration stored in ECM is same as before replacement
Click here
Learning values write
Click here
for 2KD-FTV:
  1. ECM
  1. Learning values save
  2. Learning values write
Engine starting
Click here
for 2KD-FTV:
  1. Engine assembly
  1. Injector compensation code registration
  2. Pilot quantity learning
Engine starting
for 2KD-FTV:
  1. Injector
Injector compensation code
Engine starting
for 2KD-FTV:
  1. Supply pump
Supply pump initialization
Engine startability
Click here
for 1GD-FTV:
  1. ECM
  1. Learning values save
  2. Learning values write
Engine starting
Click here
for 1GD-FTV:
  1. Engine assembly
  1. Clear crank time compensation data
  1. Input injector compensation code
  2. Pilot quantity learning
Engine starting
Click here (for Initialization)
Click here (for Registration)
for 1GD-FTV:
  1. Crankshaft position sensor plate
Clear crank time compensation data
Crank time compensation data compensation amount is same as before replacement, affecting crank time compensation data
Click here
for 1GD-FTV:
  1. Air fuel ratio sensor
Clear A/F sensor compensation data
-
for 1GD-FTV:
  1. Exhaust manifold converter sub-assembly
Clear DPF deterioration data
-
for 1GD-FTV:
  1. Injector assembly
  1. Input injector compensation code
  2. Pilot quantity learning
Engine starting
Click here
ECM
Register VIN
DTC P0630 is output
Click here (1GD-FTV)
Click here (5L-E)
Click here (1TR-FE, w/ Dual VVT-i)
Click here (2TR-FE, w/ Secondary Air Injection System)
Click here (2TR-FE, w/ Dual VVT-i)
for 1TR-FE, w/ Dual VVT-i:
  1. Throttle body
  2. Cleaning the deposits from the throttle body
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Camshaft timing exhaust gear assembly
  8. Piston or piston ring
  9. Mass air flow meter sub-assembly
  10. Fuel injector assembly
  11. Fuel pump
  12. Air fuel ratio sensor
  13. Engine coolant temperature sensor
  14. Spark plug
  15. Ignition coil assembly
  16. Air leaks from intake system
  17. Gas leaks from exhaust system
  18. Knock control sensor
Inspection after repair
Poor idle, engine starting, etc.
Click here
for 2TR-FE, w/ Dual VVT-i:
  1. Throttle body
  2. Cleaning the deposits from the throttle body
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Camshaft timing exhaust gear assembly
  8. Piston or piston ring
  9. Mass air flow meter sub-assembly
  10. Fuel injector assembly
  11. Fuel pump
  12. Engine coolant temperature sensor
  13. Spark plug
  14. Ignition coil assembly
  15. Air leaks from intake system
  16. Gas leaks from exhaust system
  17. Knock control sensor
Inspection after repair
Poor idle, engine starting, etc.
Click here
for AC60E:
  1. Automatic transmission assembly
  2. Transmission valve body assembly
  3. Any of the shift solenoid valves
Reset memory
  1. Large shift shock
  2. Engine overrun
Click here (for 1TR-FE)
Click here (for 2TR-FE)
Click here (for 1GD-FTV)
for AC60E:
  1. Automatic transmission fluid
ATF thermal degradation estimate reset
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.
  1. Tire pressure warning ECU and receiver
  2. Tire pressure warning valve and transmitter
  1. Register transmitter ID
  2. Initialize tire pressure warning system
  1. When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
  2. Tire pressure warning function
Click here (for Registration)
Click here (for Initialization)
Skid control ECU (Brake actuator assembly)
Perform yaw rate and acceleration sensor zero point calibration and store system information
Vehicle stability control system
Click here
  1. Yaw rate and acceleration sensor (airbag sensor assembly)
  2. Wheel alignment adjustment
  1. Clear zero point calibration data and store system information
  2. Perform yaw rate and acceleration sensor zero point calibration and store system information
w/ Smart Entry and Start System:
  1. Certification ECU (smart key ECU assembly)
  2. Steering lock ECU (steering lock actuator assembly)
  3. Electrical key transmitter sub-assembly
  4. ID code box (immobiliser code ECU)
  5. ECM
Code registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
w/o Smart Entry and Start System:
  1. Transponder key ECU assembly
  2. ECM
  3. Key
Code registration
Engine starting
Refer to the Service Bulletin for the registration procedure.
  1. Headlight leveling ECU assembly
  2. The vehicle height changes due to replacement of suspension components or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly LH.
Headlight leveling ECU assembly initialization
Headlight leveling function
Click here
  1. Door control transmitter
  2. Door control receiver
Registration
Wireless door lock operation
Click here
Timing belt (for 1KD-FTV, 2KD-FTV, 5L-E)
Mode reset operation
  1. Does not illuminate when replacement is necessary
  2. Illuminates when replacement is not necessary
Click here
  1. Power window master switch
  2. Power window regulator switch
  3. Power window regulator
  4. Power window motor
Motor initialization
  1. Auto up and down function
  2. Jam protection function
  3. Remote control function
Click here
← INITIALIZATION (Apr 2016 – Dec 2016)GENERAL INFORMATION (from Oct 2014) →