2014-2019 Hiace · Service Manual TRANSMISSION

P2742 Transmission Fluid Temperature Sensor "B" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The No. 2 ATF temperature sensor is installed in the transmission valve body assembly.

HINT:
  1. The temperature of ATF easily rises when towing, climbing hills, in traffic, etc.
  2. If the No. 2 ATF temperature sensor becomes short-circuited, the signal that indicates that the ATF temperature is 150°C (302°F) or higher is input into the ECM.

Vehicle conditions when the sensor is normal and when the sensor is short-circuited are indicated in the table below.
No. 2 ATF Temperature Sensor State
Detection Condition
Symptom
Recovery Condition
Sensor is normal
ATF temperature higher than 130°C (266°F)
Shift point too high
ATF temperature below 110°C (230°F)
Sensor is short-circuited
Any conditions
Shift point too high
Symptoms still occur
Engine coolant temperature higher than 95°C (203°F)
Lock-up at 3rd gear*
Symptoms still occur

HINT:
*: When ATF temperature is normal, transmission lock-up occurs in 4th, 5th and 6th gear with the shift lever in D or with the S6 range selected, in 4th or 5th gear with the S5 range selected, and 4th gear with the S4 range selected.

DTC Code
DTC Detection Condition
Trouble Area
P2742
No. 2 ATF temperature sensor resistance is below 25 Ω for 0.5 seconds or more (1 trip detection logic).
  1. Short in No. 2 ATF temperature sensor circuit
  2. No. 2 ATF temperature sensor (transmission wire)
  3. ECM
P2743
No. 2 ATF temperature sensor resistance is higher than 156 kΩ for 0.5 seconds or more and either condition is met (1 trip detection logic):
(A) 15 minutes or more have elapsed after the engine start when the engine coolant temperature or intake air temperature is -29.375°C (-20.875°F) or less.
(B) 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).
  1. Open in No. 2 ATF temperature sensor circuit
  2. No. 2 ATF temperature sensor (transmission wire)
  3. ECM

MONITOR DESCRIPTION

The No. 2 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the No. 2 ATF temperature sensor circuit. If the resistance value of the No. 2 ATF temperature sensor is below 25 Ω*1 or higher than 156 kΩ*2, the ECM interprets this as a fault in the No. 2 ATF temperature sensor or wiring. The ECM stores the DTC.
*1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on the GTS display.


WIRING DIAGRAM

Refer to DTC P0712 (Click here).

INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transmission are replaced (Click here).

HINT:
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Start the engine and wait for 15 minutes or more.
  2. Check for DTCs again (Click here).


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    1. Approx. 80°C (176°F): After stall test
    2. Equal to ambient temperature when cold soak
    If the value -40°C (-40°F) or 150°C (302°F), No. 2 ATF temperature sensor circuit is open or shorted.

    HINT:
    1. When DTC P2742 is output and the GTS indicates 150°C (302°F) or higher, there is a short circuit.
    2. When DTC P2743 is output and the GTS indicates -40°C (-40°F), there is an open circuit.
      Check the temperature displayed on the GTS in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit


1. INSPECT NO. 2 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)

  1. C319326E13
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    5 (OT2+) - 6 (OT2-)
    Always
    25 Ω to 156 kΩ
    5 (OT2+) - Body ground
    Always
    10 kΩ or higher
    6 (OT2-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
REPLACE NO. 2 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE) (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C267934E47
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D134-117 (THO2) - D134-84 (ETHO)
    Always
    25 Ω to 156 kΩ
    D134-117 (THO2) - Body ground
    Always
    10 kΩ or higher
    D134-84 (ETHO) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Jan 2017)P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (from Jan 2017) →