2014-2019 Hiace · Service Manual TRANSMISSION

P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017

DESCRIPTION

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor.
The TCM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
C294518E01
DTC No.
DTC Detection Condition
Trouble Area
P2716/77
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. TCM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM interprets this as a fault.
The TCM will turn on the MIL* and store the DTC.
*: for 1KD-FTV w/o Flex Lock Up, 2KD-FTV

WIRING DIAGRAM

C294509E04

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SLT)

  1. C113864E03
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    2 (SLT+) - 6 (SLT-)
    5.0 to 5.6 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    2 (SLT+) - Body ground
    10 kΩ or higher
    6 (SLT-) - Body ground
    ↑



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. F045523E14
    Connect the transmission wire connector to the transmission.

  1. Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    O1-20 (SLT+) - O1-19 (SLT-)
    5.0 to 5.6 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    O1-20 (SLT+) - Body ground
    10 kΩ or higher
    O1-19 (SLT-) - Body ground
    ↑



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE SLT

  1. G020767E27
    Remove the shift solenoid valve (SLT).

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (Oct 2014 – Dec 2016)P2740 Transmission Fluid Temperature Sensor "B" Circuit (+ P2742, P2743) (from Jan 2017) →