2014-2019 Hiace · Service Manual TRANSMISSION

P2740 Transmission Fluid Temperature Sensor "B" Circuit

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

DESCRIPTION

The No. 1 ATF temperature sensor is installed in the transmission valve body assembly.
The TCM applies a voltage to the temperature sensor through terminal THO of the TCM. The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases. One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The TCM calculates the fluid temperature based on the voltage signal.
DTC Code
DTC Detection Condition
Trouble Area
P2740
(a) and (b) are detected momentarily within 0.5 sec. when neither P2742 or P2743 are detected. (1-trip detection logic)
  1. No. 1 ATF temperature sensor resistance is below 25 Ω.
  2. No. 1 ATF temperature sensor resistance is higher than 156 kΩ.

HINT:
Within 0.5 sec., the malfunction switches from (a) to (b) or from (b) to (a).

  1. Open or short in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. TCM
P2742
No. 1 ATF temperature sensor voltage is below 79 Ω for 0.5 sec. or more (1-trip detection logic).
  1. Short in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. TCM
P2743
When 15 minutes or more have elapsed after the engine is started, No. 1 ATF temperature sensor voltage is higher than 156 kΩ for 0.5 sec. or more (1-trip detection logic).
  1. Open in No. 1 ATF temperature sensor circuit
  2. No. 1 ATF temperature sensor (transmission wire)
  3. TCM

MONITOR DESCRIPTION

The No. 1 ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature and detects an open or short in the No. 1 ATF temperature sensor circuit. If the resistance value of the No. 1 ATF temperature sensor is below 79 Ω*1 or higher than 156 kΩ*2, the TCM interprets this as a fault in the No. 1 ATF temperature sensor or wiring. The TCM will illuminate the MIL and store the DTC.

HINT:
  1. *1: 150°C (302°F) or higher is indicated regardless of the actual ATF temperature.
  2. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
  3. The ATF temperature can be checked on the GTS display.


WIRING DIAGRAM

C371281E03

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the GTS, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    1. After stall test: Approximately 80°C (176°F)
    2. Equal to ambient temperature when engine cold
    If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.

    HINT:
    When DTC P2742 is output and the GTS output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P2743 is output and the GTS output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the GTS in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit


1. INSPECT TRANSMISSION WIRE (NO. 1 ATF TEMPERATURE SENSOR)

  1. C214964E18
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (OT+) - 5 (OT-)
    Always
    79 Ω to 156 kΩ
    1 (OT+) - Body ground
    Always
    10 kΩ or higher
    5 (OT-) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
REPAIR OR REPLACE NO. 1 ATF TEMPERATURE SENSOR (TRANSMISSION WIRE)
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. C371285E02
    Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-25 (THO) - O1-23 (E2)
    Always
    79 Ω to 156 kΩ
    O1-25 (THO) - Body ground
    Always
    10 kΩ or higher
    O1-23 (E2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P2716/77 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Jan 2017)P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (from Jan 2017) →