2014-2019 Hiace · Service Manual TRANSMISSION

P0973/62 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)

Diagnostic trouble codes · Vehicles built from Oct 2014

Also covers:

DESCRIPTION

Shifting from 1st to 4th (O/D) is performed in combination with "ON" and "OFF" operation of the shift solenoid valves S1, S2 and SL which are controlled by the TCM. If an open or short circuit occurs in either of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0973/62
TCM detects short in solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1-trip detection logic)
  1. Short in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. TCM
P0974/62
TCM detects open in solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1-trip detection logic)
  1. Open in shift solenoid valve S1 circuit
  2. Shift solenoid valve S1
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. When the shift solenoid valve S1 is on, if resistance is 8 Ω or less, the TCM determines there is a short in the shift solenoid valve S1 circuit.
When the shift solenoid valve S1 is off, if resistance is 100 kΩ or more, the TCM determines there is an open in the shift solenoid valve S1 circuit (Click here).

WIRING DIAGRAM

C294508E10

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (S1)

  1. C113864E01
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    4 - Body ground
    11 to 15 Ω



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)

  1. F045523E12
    Connect the transmission connector to the transmission.

  1. Disconnect the connector from the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    O1-18 (S1) - Body ground
    11 to 15 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM

3. INSPECT SHIFT SOLENOID VALVE S1

  1. G038832E01
    Remove the shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (S1) - Solenoid Body (S1)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE S1
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0756/63 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) (from Jan 2017)P0976/63 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977/63) (from Oct 2014) →