2014-2019 Hiace · Service Manual TRANSMISSION

P0712/38 Transmission Fluid Temperature Sensor "A" Circuit Low Input

Diagnostic trouble codes · Vehicles built from Oct 2014

Also covers:

DESCRIPTION

The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the TCM.
The TCM applies a voltage to the temperature sensor through TCM terminal THOC.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The TCM calculates the fluid temperature based on the voltage signal.
DTC No.
DTC Detection Condition
Trouble Area
P0712/38
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic)
  1. Short in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. TCM
P0713/38
ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more have elapsed after the engine start
DTC is detected for 0.5 sec. or more (1-trip detection logic)
  1. Open in ATF temperature sensor circuit
  2. ATF temperature sensor
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.
*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

HINT:
The ATF temperature can be checked on the Intelligent Tester display.


WIRING DIAGRAM

C251069E02

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the tester, read the Data List.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 3
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature when engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), ATF temperature sensor circuit is opened or short circuited

    HINT:
    When DTC P0712 is stored and the intelligent tester output is 150°C (302°F) or higher, there is a short circuit.
    When DTC P0713 is stored and the intelligent tester output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the tester in order to check if a malfunction exists.

    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or higher
    Short circuit
    If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately stored (in 0.5 seconds). When P0713 is stored, P0711 cannot be stored. It is not necessary to inspect the circuit when P0711 is stored.


1. INSPECT ATF TEMPERATURE SENSOR

  1. C251072E01
    Disconnect the ATF temperature sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    79 Ω to 156 kΩ
    1 - Body ground
    Always
    10 kΩ or higher
    2 - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Standard Resistance:
    ATF Temperature
    Specified Condition
    20°C (68°F)
    10.3 to 13.9 kΩ
    110°C (230°F)
    0.68 to 0.88 kΩ

Text in Illustration 
*a
Component without harness connected
(ATF Temperature Sensor (for 1KD-FTV w/ DPF))
*b
Component without harness connected
(ATF Temperature Sensor (for 1KD-FTV w/o DPF, for 2KD-FTV))


NG
REPLACE ATF TEMPERATURE SENSOR
OK


2. CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - TCM)

  1. C212047E30
    Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-24 (THOC) - O1-23 (E2)
    Always
    79 Ω to 156 kΩ
    O1-24 (THOC) - Body ground
    Always
    10 kΩ or higher
    O1-23 (E2) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0711 Transmission Fluid Temperature Sensor "A" Performance (from Oct 2014)P0717/67 Input Speed Sensor Circuit No Signal (from Oct 2014) →