2014-2019 Hiace · Service Manual TRANSMISSION

P0717/67 Input Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The O/D direct clutch speed sensor (NC0) detects the rotation speed of the O/D input shaft from the rotation of the O/D direct clutch drum. Its construction is the same as that of the speed sensor (SP2).
By comparing the O/D direct clutch speed signal and speed sensor (SP2) signal, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure in response to various conditions, thus achieving smooth gear shift.
C113862E02
DTC No.
DTC Detection Condition
Trouble Area
P0717/67
  1. All conditions below are detected for 5 sec. or more.
    (1KD-FTV: 1-trip detection logic)
    (2KD-FTV: 2-trip detection logic)
    1. Gear change is not performed
    2. Gear position: 1st, 2nd or 3rd
    3. T/M input shaft rpm: 300 rpm or less
    4. T/M output shaft rpm: 500 rpm or more
    5. Park/neutral position switch:
      1. NSW input signal is OFF
      2. R input signal is OFF
      3. L input signal is OFF
    6. Shift solenoid valves and park/neutral position switch are in normal operation.
  1. Open or short in speed sensor (NC0) circuit
  2. Speed sensor (NC0)
  3. TCM
  4. Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals NC0+ and NC0- of the TCM connector.
G034873E03

Standard:
Refer to the illustration.

HINT:
Gauge setting.
Terminal
NC0+ - NC0-
Tool setting
5 V/DIV, 0.5 ms/DIV
Vehicle condition
Engine idle speed (P or N position)


MONITOR DESCRIPTION

This DTC indicates that pulse is not output from the speed sensor NC0 (O/D (input) speed sensor) or is output only little. The NC0 terminal of the TCM detects the revolving signal from speed sensor (NC0) (input RPM). The TCM outputs a gearshift signal comparing the input speed sensor (NC0) with the output speed sensor (SP2).
When the output shaft speed is higher than the expected value and the input shaft speed is 300 rpm or less while running with the shift lever on D, the TCM will conclude that there is a malfunction of the input speed sensor (NC0). The TCM will illuminate the MIL and a DTC is set.

WIRING DIAGRAM

C109043E03

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Power train / ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    Measurement Item /
    Range
    Normal Condition
    SPD (NC0)
    Input Turbine Speed/
    display: 50 r/min

    HINT:
    1. Lock-up ON (warmed up engine, other than O/D):
      Input Turbine Speed (NC0) is equal to engine speed
    1. Lock-up ON (warmed up engine, O/D):
      Input Turbine Speed (NC0) is 0 rpm
    1. Lock-up OFF (Idling with shift lever on N):
      Input Turbine Speed (NC0) is nearly equal to engine speed

    HINT:
    1. SPD (NC0) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NC0) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. INSPECT SPEED SENSOR INSTALLATION

  1. BR03795E34
    Check the speed sensor (NC0) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR (NC0)
OK


2. INSPECT SPEED SENSOR (NC0)

  1. C113863E08
    Disconnect the speed sensor connector from the transmission.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (NC0)
OK


3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR - TCM)

  1. F045523E31
    Connect the speed sensor connector.

  1. Disconnect the TCM connector.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    O1-3 (NC0+) - O1-2 (NC0-)
    560 to 680 Ω

  1. Measure the resistance.

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    O1-3 (NC0+) - Body ground
    10 kΩ or higher
    O1-2 (NC0-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0712/38 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713/38) (from Oct 2014)P0722/61 Output Speed Sensor Circuit No Signal (from Oct 2014) →