2014-2019 Hiace · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Dec 2016 from Jan 2017


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Powertrain / ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm
    Max.: 16383.75 rpm
    Engine idling: 700 to 800 rpm
    -
    Calculate Load
    Load calculated by ECM/
    Min.: 0%
    Max.: 100%
    1. Engine idling: 11.4 to 16.4%
    2. Running without load (2500 rpm): 13.1 to 18.9%
    -
    Coolant Temp
    Engine coolant temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    After warming up engine: 80 to 100°C (176 to 212°F)
    1. If the value is -40°C (-40°F) , the sensor circuit is open
    2. If the value is 140°C (284°F), the sensor circuit is shorted.
    Engine Run Time
    Engine run time/
    Min.: 0 s
    Max.: 65535 s
    Time after engine start
    -
    Battery Voltage
    Battery voltage/
    Min.: 0 V
    Max.: 65.535 V
    Engine idling: 11 to 14 V
    -
    Glow Indicator Supported
    Status of the Glow Indicator Supported/
    Unsupp or Supp
    -
    -
    Glow Indicator
    Status of the Glow Indicator/
    ON or OFF
    -
    -
    Starter Signal
    Status of the Starter Signal/
    ON or OFF
    1. ON: Engine cranking
    2. OFF: Engine not cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On P or N: ON
    2. Not on P or N: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. Brake pedal is depressed: ON
    2. Brake pedal is released: OFF
    -
    Check Mode
    Status of the Check Mode/
    ON or OFF
    ON: Check mode on
    -
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    Comprehensive Component Monitor.
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    Fuel System Monitor.
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    Misfire Monitor.
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S (A/FS) Heater Monitor
    Heated oxygen sensor (air fuel ratio sensor) heater monitor/
    Not Avl or Avail
    -
    -
    O2S (A/FS) Heater Monitor
    Heated oxygen sensor (air fuel ratio sensor) heater monitor/
    Compl or Incmpl
    -
    -
    O2S (A/FS) Monitor
    Heated oxygen sensor (air fuel ratio sensor) monitor/
    Not Avl or Avail
    -
    -
    O2S (A/FS) Monitor
    Heated oxygen sensor (air fuel ratio sensor) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    # Codes(Include History)
    Number of emission related DTCs/
    Min.: 0
    Max.: 255
    -
    -
    MIL
    MIL status/
    ON or OFF
    ON: MIL on
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 minute
    Max.: 65535 minutes
    Equivalent to running time after MIL ON
    -
    Time after DTC Cleared
    Time after DTCs cleared/
    Min.: 0 minute
    Max.: 65535 minutes
    Equivalent to time after DTCs cleared
    -
    Distance from DTC Cleared
    Distance driven after DTCs cleared/
    Min.: 0 km (0 mile)
    Max.: 65535 km (40723 mile)
    Equivalent to distance driven after DTCs cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycles after DTCs cleared/
    Min.: 0
    Max.: 255
    -
    Number of warm-up cycles after DTCs are cleared.
    OBD Requirements
    OBD requirement
    -
    -
    Number of Emission DTC
    Emissions-related DTCs/
    Min.: 0
    Max.: 127
    -
    -
    TC and TE1
    TC and TE1 terminals of DLC3/
    ON or OFF
    -
    Active Test support data.
    Total Distance Traveled
    Total Distance Traveled/
    Min.: 0 km (0 mile)
    Max.: 16777215 km (10425361 mile)
    -
    -
    Model Code
    Model code
    -
    Identifying model code.
    Transmission (Engine) Type
    Transmission (Engine) Type
    -
    -
    Cylinder Number
    Number of cylinders/
    Min.: 0
    Max.: 255
    -
    -
    Transmission Type
    Transmission type/
    -
    -
    Destination
    Destination
    -
    -
    Model Year
    Model year/
    Min.: 1900
    Max.: 2155
    -
    -
    System Identification
    System identification
    -
    -
    Accel Position from EFI
    Absolute Accelerator Pedal Position/
    Min.: 0%
    Max.: 100%
    -
    -
    Injection Volume from EFI
    Injection volume/
    Min.: 0 mm3/st
    Max.: 1279.98 mm3/st
    Engine idling: 3.0 to 10.0 mm3/st
    Injection volume received from the ECM.
    SPD (NC0)
    Input turbine speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (warmed up engine, not in O/D):
      Input turbine speed (NC0) is equal to the engine speed
    2. Lock-up ON (warmed up engine, O/D):
      Input turbine speed (NC0) is 0 rpm
    3. Lock-up OFF (idling with shift lever on N):
      Input turbine speed (NC0) is nearly equal to engine speed
    The data is displayed in increments of 50 rpm.
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph)
    (output shaft speed is equal to vehicle speed)
    -
    Shift SW Status (P Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. On P: ON
    2. Not on P: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (R Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On R: ON
    2. Not on R: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (2 Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On 2: ON
    2. Not on 2: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (L Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On L: ON
    2. Not on L: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On N: ON
    2. Not on N: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (N, P Range) Supported
    Status of park/neutral position switch (N or P) supported/
    Unsupp or Supp
    -
    -
    Shift SW Status (N, P Range)
    Park/neutral position switch status/
    ON or OFF
    Shift lever is:
    1. On N or P: OFF
    2. Not on N or P: ON
    -
    Shift SW Status (D Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On D or 3: ON
    2. Not on D or 3: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    Shift SW Status (3 Range)
    PNP switch status/
    ON or OFF
    Shift lever is:
    1. On 3: ON
    2. Not on 3: OFF
    When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect.

    HINT:
    When failure still occurs even after adjusting these parts, refer to DTC P0705 (Click here).

    A/T Oil Temperature 3
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall speed test: Approximately 80°C (176°F)
    2. While engine is cold: Equal to ambient temperature
    If the value is -40°C (-40°F) or 215°C (419°F), the ATF temperature sensor circuit is open or shorted.
    Lock Up
    Lock-up/
    ON or OFF
    1. ON: Lock-up operating
    2. OFF: Lock-up not operating
    -
    Shift Status
    TCM gear shift command/
    1st, 2nd, 3rd or 4th (O/D)
    Shift lever position is:
    1. On L: 1st
    2. On 2: 1st or 2nd
    3. On 3: 1st, 2nd or 3rd
    4. On D (O/D ON): 1st, 2nd, 3rd or 4th (O/D)
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    Shift solenoid SLT is:
    1. ON: Operating
    2. OFF: Not operating
    -
    SL Solenoid Status
    Shift solenoid SL status/
    ON or OFF
    Shift solenoid SL is:
    1. ON: Operating
    2. OFF: Not operating
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Powertrain / ECT / Active Test".

  7. Follow the instructions on the tester and perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Shift lever in P or N
    Activate the Solenoid (SLT)*
    Operate shift solenoid valve SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling
    Activate the Solenoid (S1)
    Operate shift solenoid valve S1
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine stopped
    3. Shift lever in P or N
    Activate the Solenoid (S2)
    Operate shift solenoid valve S2
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine stopped
    3. Shift lever in P or N
    Activate the Lock Up
    Control shift solenoid valve SL to set automatic transmission to lock-up
    ON or OFF
    Possible to check shift solenoid valve SL operation.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35%
    2. Vehicle speed: 60 km/h (37 mph) or more
    Activate the Solenoid (SL)
    Operate shift solenoid valve SL
    ON or OFF
    [Vehicle Condition]
    1. Ignition switch ON
    2. Engine stopped
    3. Shift lever in P or N
    Control the Shift Position
    Operate shift solenoid valves and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of the shift solenoid valves.
    [Vehicle Condition]
    50 km/h (31 mph) or less
    *: "Activate the Solenoid (SLT)" in the ACTIVE TEST is performed to check the line pressure changes by connecting the SST to the automatic transmission, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in ACTIVE TEST and HYDRAULIC TEST are different from each other.

← FAIL-SAFE CHART (from Oct 2014)DATA LIST / ACTIVE TEST (Jan 2015 – Dec 2016) →