2014-2019 Hiace · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT FRONT DOOR LOCK ASSEMBLY (DRIVER SIDE)

  1. B111190E01
    Inspect the door lock motor & unlock detection switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      ON (Door lock set to UNLOCK)
      7 - 8 (Below 1 Ω)
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      OFF (Door lock set to LOCK)
      7 - 8 (10 kΩ or higher)

    2. B111184E01
      Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      ON (Door lock set to UNLOCK)
      7 - 8 (Below 1 Ω)
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      OFF (Door lock set to LOCK)
      7 - 8 (10 kΩ or higher)

  1. B111189E01
    Inspect the key lock and unlock switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      10 - 7
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      9 - 7
      OFF (Door lock set to LOCK)
      Below 1 Ω

    2. B111193E01
      Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      5 - 8
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      6 - 8
      OFF (Door lock set to LOCK)
      Below 1 Ω


REMOVE FRONT DOOR LOCK ASSEMBLY (FRONT PASSENGER SIDE)

  1. B111184E01
    Inspect the door lock motor.

    1. Apply battery voltage and check operation of the door lock motor.

      Standard:
      LHD Models:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock

    2. B111190E01
      Apply battery voltage and check operation of the door lock motor.

      Standard:
      RHD Models:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock

  1. B111193E01
    Inspect the key lock and unlock switch.

    1. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      LHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      5 - 8
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      6 - 8
      OFF (Door lock set to LOCK)
      Below 1 Ω

    2. B111189
      Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard resistance:
      RHD Models:
      Tester Connection
      Door Lock Condition
      Specified Condition
      10 - 7
      ON (Door lock set to UNLOCK)
      Below 1 Ω
      9 - 7
      OFF (Door lock set to LOCK)
      Below 1 Ω

← INSPECTION (from Oct 2014)INSPECTION (from Oct 2014) →