2014-2019 Hiace · Service Manual TRANSMISSION

P0717 Input Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The O/D direct clutch speed sensor (NCO) detects the rotation speed of the O/D input shaft from the rotation of the O/D direct clutch drum. Its construction is the same as that of the speed sensor (SP2).
By comparing the O/D direct clutch speed signal and speed sensor (SP2) signal, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure in response to various conditions, thus achieving smooth gear shift.
C113862E01
DTC No.
DTC Detection Condition
Trouble Area
P0717
  1. All conditions below are detected for 5 secs. or more
    (1-trip detection logic)
    1. Gear change is not performed
    2. Gear position: 1st, 2nd or 3rd
    3. T/M input shaft rpm: 300 rpm or less
    4. T/M output shaft rpm: 500 rpm or more
    5. Park/neutral position switch:
      1. NSW input signal is OFF
      2. R input signal is OFF
      3. L input signal is OFF
    6. Shift solenoid valves and park/neutral position switch are in normal operation
  1. Open or short in speed sensor (NCO) circuit
  2. Speed sensor (NCO)
  3. ECM
  4. Automatic transmission (clutch, brake or gear, etc.)
Reference (Using an oscilloscope):
Check the waveform between terminals NCO+ and NCO- of the ECM connector.
G034873E06

Standard:
Refer to the illustration.

HINT:
Gauge setting
Terminal
NCO+ - NCO-
Tool setting
5 V/DIV., 0.5 ms/DIV.
Vehicle condition
Engine idling (P or N position)


MONITOR DESCRIPTION

This DTC indicates that pulse is not output from the speed sensor NCO (O/D (input) speed sensor) or is output only a little. The NCO terminal of the ECM detects the speed signal from the speed sensor (NCO) (input RPM). The ECM outputs a gearshift signal comparing the input speed sensor (NCO) with the output speed sensor (SP2).
When the output shaft speed is higher than the expected value and the input shaft speed is 300 rpm or less while running with the shift lever on D, the ECM will conclude that there is a malfunction of the input speed sensor (NCO). The ECM will illuminate the MIL and a DTC is set.

WIRING DIAGRAM

C294507E05

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Intelligent Tester to the DLC3.

  4. Turn the ignition switch to the ON position.

  5. Turn on the tester.

  6. Select the item "Enter / Powertrain / Engine and ECT / Data List".

  7. Follow the instructions on the tester and read the Data List.

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    SPD (NCO)
    Input Turbine Speed/
    display: 50 r/min

    HINT:
    1. Lock-up ON (warmed up engine, other than O/D):
      Input Turbine Speed (NCO) is equal to engine speed
    1. Lock-up ON (warmed up engine, O/D):
      Input Turbine Speed (NCO) is 0 rpm
    1. Lock-up OFF (Idling with shift lever on N):
      Input Turbine Speed (NCO) is nearly equal to engine speed

    HINT:
    1. SPD (NCO) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NCO) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble of the circuit.


1. INSPECT SPEED SENSOR INSTALLATION

  1. BR03795E34
    Check the speed sensor (NCO) installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



NG
REPLACE SPEED SENSOR (NCO)
OK


2. INSPECT SPEED SENSOR (NCO)

  1. C206284E12
    Disconnect the speed sensor (NCO) connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Speed Sensor (NCO))



NG
REPLACE SPEED SENSOR (NCO)
OK


3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)

  1. C302055E10
    Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    D97-122 (NCO+) - D97-100 (NCO-)
    560 to 680 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    D97-122 (NCO+) - Body ground
    10 kΩ or higher
    D97-100 (NCO-) - Body ground
    ↑

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0710 Transmission Fluid Temperature Sensor "A" Circuit (+ P0712, P0713) (from Oct 2014)P0722 Output Speed Sensor Circuit No Signal (from Oct 2014) →