P0710 Transmission Fluid Temperature Sensor "A" Circuit
Diagnostic trouble codes · Vehicles built from Oct 2014
Also covers:
- P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input
- P0713 Transmission Fluid Temperature Sensor "A" Circuit High Input
DESCRIPTION
The ATF (Automatic Transmission Fluid) temperature sensor converts the fluid temperature into a resistance value which is input into the ECM.

The ECM applies a voltage to the temperature sensor through ECM terminal THOC.
The sensor resistance changes with the transmission fluid temperature. As the temperature becomes higher, the sensor resistance decreases.
One terminal of the sensor is grounded so that the sensor resistance decreases and the voltage goes down as the temperature becomes higher.
The ECM calculates the fluid temperature based on the voltage signal.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0710 |
|
|
| P0712 |
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic) |
|
| P0713 |
ATF temperature sensor resistance is more than 156 kΩ when 15 minutes or more have elapsed after the engine start DTC is detected for 0.5 sec. or more (1-trip detection logic) |
|
MONITOR DESCRIPTION
These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and the ECM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the ECM interprets this as a fault in the ATF sensor or wiring. The ECM will turn on the MIL and store the DTC.*1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
*2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.
- HINT:
- The ATF temperature can be checked on the Intelligent Tester display.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the Intelligent Tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Enter / Powertrain / Engine and ECT / Data List".
Follow the instructions on the tester and read the Data List.
Item
Measurement Item/
Range (display)
Normal Condition
A/T Oil Temperature 3
ATF Temp. Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
- After Stall Test;
Approx. 80°C (176°F)
- Equal to ambient temperature when cold soak
- HINT:
- When DTC P0712 is output and Intelligent Tester output is 150°C (302°F) or more, there is a short circuit.
- When DTC P0713 is output and Intelligent Tester output is -40°C (-40°F), there is an open circuit.
- Measure the resistance between terminal THOC and body ground.
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
150°C (302°F) or more
Short circuit
- HINT:
- If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 second).
- After Stall Test;
| 1. INSPECT ATF TEMPERATURE SENSOR |
Disconnect the ATF temperature sensor connector from the transmission.

Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Specified Condition
1 - 2
79 Ω to 156 kΩ
1 - Body ground
10 kΩ or higher
2 - Body ground
10 kΩ or higher
- HINT:
- If the resistance is out of the specified range at either of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.
- Resistance:
ATF Temperature
Specified Condition
20°C (68°F)
10.3 to 13.9 kΩ
110°C (230°F)
0.68 to 0.88 kΩ
| *a |
Component without harness connected (ATF temperature sensor) |
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - ECM) |
Connect the ATF temperature sensor connector to the transmission.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Specified Condition
D97-114 (THOC) - D97-72 (E2)
79 Ω to 156 kΩ
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Specified Condition
D97-114 (THOC) - Body ground
10 kΩ or higher
D97-72 (E2) - Body ground
↑
| *a |
Front view of wire harness connector (to ECM) |
|
|
||||
| OK | ||
| ||
