2014-2019 Hiace · Service Manual TRANSMISSION

P0724/95 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up condition when brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the TCM. Then the TCM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724/95
The stop light switch remains ON even when the vehicle repeats 5 cycles of STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more).
(2-trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. TCM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during "stop and go" driving, the TCM interprets this as a fault in the stop light switch and the MIL comes on and the TCM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for 2 driving cycles in order to detect a malfunction.

WIRING DIAGRAM

C301451E01

INSPECTION PROCEDURE


When using intelligent tester:


1. READ VALUE USING DATA LIST (STP SIGNAL)
  1. DATA LIST

    HINT:
    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to the ON position.

    4. Turn on the tester.

    5. Select the item "Powertrain / ECT / Data List".

    6. Follow the instructions on the tester and read the Data List.

      Standard:
      Item
      Measurement Item /
      Range (display)
      Normal Condition
      Stop Light Switch
      Stop light SW Status/
      ON or OFF
      1. Brake Pedal is depressed: ON
      2. Brake Pedal is released: OFF

      NOTICE:
      In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty or not.



OK
Go to step 3
NG


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. E065594E05
    Remove the stop light switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin free
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

  1. G037243E05
    Install the stop light switch assembly.

  1. Measure the voltage when the brake pedal is depressed and released.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O3-14 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    Brake pedal is released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


When not using intelligent tester:


1. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. E065594E05
    Remove the stop light switch assembly.

  1. Measure the resistance.

    Standard resistance:
    Tester Connection
    Switch Position
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin free
    10 kΩ or higher
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY
OK


2. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - TCM)

  1. G037243E05
    Install the stop light switch assembly.

  1. Measure the voltage when the brake pedal is depressed and released.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O3-14 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    Brake pedal is released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← P0722/61 Output Speed Sensor Circuit No Signal (from Oct 2014)P0741/64 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (Oct 2014 – Dec 2016) →