P0722/61 Output Speed Sensor Circuit No Signal
Diagnostic trouble codes · Vehicles built from Oct 2014
DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the TCM. The TCM determines the vehicle speed based on these signals.An AC voltage is generated in the speed sensor SP2 coil as the rotor mounted on the output shaft rotates, and this voltage is sent to the TCM.
The gear shift point and lock-up timing are controlled by the TCM based on the signals from this speed sensor and throttle position sensor.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0722 |
|
|
Check the waveform between terminals SP2+ and SP2- of the TCM connector.


- Standard:
- Refer to the illustration.
- HINT:
- Gauge setting.
Terminal
SP2+ - SP2-
Tool setting
2V/DIV, 20ms/DIV
Vehicle condition
Vehicle speed 20 km/h (12 mph)
MONITOR DESCRIPTION
The output speed sensor SP2 monitors the output shaft speed. The TCM controls the gearshift point and the lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.If the TCM detects no signal from the output shaft speed sensor SP2 even while the vehicle is moving, it will conclude that is a malfunction of the output speed sensor SP2. The TCM will illuminate the MIL and set a DTC.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the Intelligent Tester Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to shorten labor time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the Intelligent Tester to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Enter / Power train / ECT / Data List".
Follow the instructions on the tester and read the Data List.
Item
Measurement Item /
Range (display)
Normal Condition
SPD (SP2)
Output shaft Speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) - HINT:
- Equal to vehicle speed
- HINT:
- SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit.
- The SPD (SP2) value displayed on the tester is much lower than the actual vehicle speed:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (SP2) is always 0 while driving:
| 1. INSPECT SPEED SENSOR INSTALLATION |
Check the speed sensor (SP2) installation.

- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR (SP2) |
Disconnect the speed sensor connector from the transmission.

Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Specified Condition
20°C (68°F)
1 - 2
560 to 680 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR - TCM) |
Connect the speed sensor connector.

Disconnect the TCM connector.
Measure the resistance according to the value(s) in the table below.
- Resistance:
Tester Connection
Specified Condition
20°C (68°F)
O1-30 (SP2+) - O1-29 (SP2-)
560 to 680 Ω
Measure the resistance according to the value(s) in the table below.
- Resistance (Check for short):
Tester Connection
Specified Condition
O1-30 (SP2+) - Body ground
10 kΩ or higher
O1-29 (SP2-) - Body ground
↑
|
|
||||
| OK | ||
| ||
