2014-2019 Hiace · Service Manual TRANSMISSION

P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL)

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Also covers:

DESCRIPTION

Shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.
DTC Code
DTC Detection Condition
Trouble Area
P2769
The ECM detects a short in the shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (2-trip detection logic).
  1. Short in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. ECM
P2770
The ECM detects an open in the shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (2-trip detection logic).
  1. Open in shift solenoid valve SL circuit
  2. Shift solenoid valve SL
  3. ECM
Fail-safe function:
If the ECM detects a malfunction, it turns shift solenoid valve SL OFF.

MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on engine speed, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The ECM determines the lock-up status of the torque converter by comparing the engine speed (NE) to the input speed (NC0). The ECM calculates the actual transmission gear by comparing the input speed (NC0) to the output speed (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to shift solenoid valve SL. When shift solenoid valve SL is opened, shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter. If the ECM detects an open or short in shift solenoid valve SL circuit, the ECM interprets this as a fault in shift solenoid valve SL or its circuit. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C294508E06

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

  1. C214964E13
    Disconnect the transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    7 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C302055E08
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D97-61 (SL) - Body ground
    20°C (68°F)
    11 to 15 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SL

  1. C238276E01
    Remove shift solenoid valve SL.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid valve SL connector terminal - Shift solenoid valve SL body
    20°C (68°F)
    11 to 15 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) → Shift solenoid valve SL connector
    2. Battery negative (-) → Shift solenoid valve SL body
    Valve moves and makes an operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL)


NG
REPLACE SHIFT SOLENOID VALVE SL
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (Oct 2014 – Dec 2014)ON-VEHICLE INSPECTION (Oct 2014 – Dec 2014) →