2014-2019 Hiace · Service Manual TRANSMISSION

P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2)

Diagnostic trouble codes · Vehicles built from Oct 2014

Also covers:

DESCRIPTION

Shifting from 1st to 4th (O/D) is performed in combination with "ON" and "OFF" operation of the shift solenoid valves S1, S2 and SL which are controlled by the ECM. If an open or short circuit occurs in either of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0976
ECM detects short in solenoid valve S2 circuit 2 times when solenoid valve S2 is operated (1-trip detection logic)
  1. Short in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. ECM
P0977
ECM detects open in solenoid valve S2 circuit 2 times when solenoid valve S2 is not operated (1-trip detection logic)
  1. Open in shift solenoid valve S2 circuit
  2. Shift solenoid valve S2
  3. ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S2 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem and illuminates the MIL and stores the DTC. When the shift solenoid valve S2 is on, if resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S2 circuit.
When the shift solenoid valve S2 is off, if resistance is 100 kΩ or more, the ECM determines there is an open in the shift solenoid valve S2 circuit (Click here).

WIRING DIAGRAM

C294508E08

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (S2)

  1. C214964E15
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    8 - Body ground
    11 to 15 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C302055E14
    Connect the transmission connector to the transmission.

  1. Disconnect the connector from the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    D97-55 (S2) - Body ground
    11 to 15 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE S2

  1. G038833E02
    Remove the shift solenoid valve S2.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    Solenoid Connector (S2) - Solenoid Body (S2)
    11 to 15 Ω

  1. Connect the positive (+) lead to the terminal of the solenoid connector, and the negative (-) lead to the solenoid body.

    OK:
    The solenoid makes an operating sound.

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve S2)


NG
REPLACE SHIFT SOLENOID VALVE S2
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0973 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) (+ P0974) (from Oct 2014)P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (from Oct 2014) →