2014-2019 Hiace · Service Manual TRANSMISSION

P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

Diagnostic trouble codes · Vehicles built from Oct 2014

DESCRIPTION

The linear solenoid valve (SLT) controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor.
The ECM adjusts the duty cycle of the SLT solenoid valve to control hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
(*): Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B is the period of non-continuity, then
Duty Ratio = A/(A + B) x 100 (%)
C108924E03
DTC No.
DTC Detection Condition
Trouble Area
P2716
Open or short is detected in shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
  1. Open or short in shift solenoid valve SLT circuit
  2. Shift solenoid valve SLT
  3. ECM

MONITOR DESCRIPTION

When an open or short in the linear solenoid valve (SLT) circuit is detected, the ECM interprets this as a fault.
The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C294509E03

INSPECTION PROCEDURE


1. INSPECT TRANSMISSION WIRE (SLT)

  1. C214964E16
    Disconnect the transmission wire connector from the transmission.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    2 (SLT+) - 6 (SLT-)
    5.0 to 5.6 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    2 (SLT+) - Body ground
    10 kΩ or higher
    6 (SLT-) - Body ground
    ↑

Text in Illustration 
*a
Component without harness connected
(Transmission Wire)


NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C302055E15
    Connect the transmission wire connector to the transmission.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    D97-54 (SLT+) - D97-53 (SLT-)
    5.0 to 5.6 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Resistance (Check for short):
    Tester Connection
    Specified Condition
    D97-54 (SLT+) - Body ground
    10 kΩ or higher
    D97-53 (SLT-) - Body ground
    ↑

Text in Illustration 
*a
Front view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

3. INSPECT SHIFT SOLENOID VALVE SLT

  1. C197715E24
    Remove the shift solenoid valve (SLT).

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Specified Condition
    20°C (68°F)
    1 - 2
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, and then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SLT)


NG
REPLACE SHIFT SOLENOID VALVE SLT
OK

REPAIR OR REPLACE TRANSMISSION WIRE


← P0976 Shift Solenoid "B" Control Circuit Low (Shift Solenoid Valve S2) (+ P0977) (from Oct 2014)P2769 Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (+ P2770) (from Oct 2014) →