2014-2019 Hiace · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Oct 2014 – Dec 2016

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017


1. DRAIN ENGINE COOLANT

A316990E01

CAUTION:
To avoid the danger of being burned, do not remove the reservoir cap while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.

  1. Loosen the radiator drain plug.

  1. Remove the reservoir cap.

  1. Loosen the cylinder block drain plug and drain the coolant.

  1. Tighten the radiator drain plug.

  1. Tighten the cylinder block drain plug.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


2. DRAIN ENGINE OIL

3. REMOVE FRONT SEAT ASSEMBLY RH

  1. B107528
    Move the front seat assembly fully forward.

  1. Remove the 2 bolts on the rear side of the seat.

  1. Move the front seat assembly to the rearmost position.

  1. Remove the 2 bolts on the front side of the seat.

  1. Move the front seat assembly to the center of the seat slide rail. Set the seatback in the upright position.

  1. Disconnect the front seat inner belt assembly connector.

  1. Remove the front seat assembly.


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE ENGINE SERVICE HOLE SUB COVER SUB-ASSEMBLY
  1. Turn back the carpet, and remove the engine service hole cover sub-assembly.


6. REMOVE INTAKE AIR CONNECTOR SUB-ASSEMBLY
  1. Disconnect the ventilation hose.

  1. Disconnect the turbo pressure sensor connector.

  1. A111051
    Remove the bolt, 3 nuts, intake air connector and gasket.


7. REMOVE INTAKE AIR CONNECTOR BRACKET

  1. A112061
    Remove the 2 bolts and intake air connector bracket.


8. REMOVE OIL LEVEL GAGE SUB-ASSEMBLY

9. REMOVE OIL LEVEL GAGE GUIDE
  1. Remove the 2 bolts, oil level gage and oil level gage guide.


10. REMOVE VANE PUMP V BELT

  1. A071310E01
    Loosen the bolt A and nut B, and remove the V belt.


11. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1 (w/ Air Conditioning System)

  1. A074095E01
    Loosen the nut A and bolt B, and remove the V belt.


12. REMOVE FAN & GENERATOR V BELT (w/o Air Conditioning)

  1. A115631E01
    Loosen the bolts A and B, and remove the V belt.


13. REMOVE FAN & GENERATOR V BELT (w/ Air Conditioning System)

  1. A115632E01
    Loosen the bolts A and B.

  1. Loosen the adjusting bolt C, and remove the V belt.


14. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH (w/ Air Conditioning System)
(Click here)

15. REMOVE COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A112014
    Remove the 3 bolts and compressor mounting bracket.

  1. A112016
    Remove the bolt and spacer.

  1. A112015
    Remove the 4 bolts and compressor mounting bracket.


16. REMOVE GENERATOR W/ VACUUM PUMP ASSEMBLY
  1. Remove the terminal cover and nut, and disconnect the +B terminal wire.

  1. A113536
    Disconnect the connector.

  1. Disconnect the vacuum hose.

  1. Disconnect the oil outlet hose.

  1. Remove the union nut and gasket, and disconnect the vacuum pump inlet hose.

  1. A113355
    Remove the bolt and generator w/ vacuum pump assembly.


17. REMOVE EXHAUST PIPE ASSEMBLY FRONT
(Click here)

18. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO.1
  1. Remove the 3 bolts and exhaust manifold heat insulator No.1.


19. REMOVE EXHAUST MANIFOLD

  1. A113082
    Remove the 6 bolts, 2 nuts and exhaust manifold.

  1. Remove the exhaust manifold gasket from the cylinder head.


20. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Using SST, remove the oil filter.

    SST
    09228-44011  


21. REMOVE VACUUM PUMP OIL INLET HOSE

  1. A113492
    Remove the union bolt and 2 gaskets, and disconnect the vacuum pump oil inlet hose from the cylinder block.


22. REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

  1. A113493
    Remove the 10 bolts, 2 nuts, oil filter bracket, and gasket.


23. REMOVE OIL COOLER ASSEMBLY
  1. Remove the 4 nuts, oil cooler, and 2 gaskets.

← COMPONENTS (from Oct 2014)REMOVAL (from Jan 2017) →