2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

  1. D029023
    Remove the manual transmission filler plug and gasket from the manual transmission case.


2. REMOVE MANUAL TRANSMISSION DRAIN PLUG

  1. D029024
    Remove the manual transmission drain plug and gasket from the manual transmission case.


3. REMOVE CLUTCH HOUSING

  1. D029028
    Remove the 9 bolts.

  1. D029029
    Using a plastic-faced hammer, remove the clutch housing from the manual transmission case.


4. REMOVE BACK UP LIGHT SWITCH ASSEMBLY

  1. C114270E01
    Using SST, remove the back up light switch assembly and gasket from the manual transmission case.
    SST
    09817-16011  


5. REMOVE SPEEDOMETER SENSOR
  1. Remove the bolt and speedometer sensor from the extension (MTM) housing sub-assembly.

  1. Remove the O-ring from the speedometer sensor.


6. REMOVE EXTENSION HOUSING(MTM) COVER

  1. C112987
    Remove the 6 bolts, extension housing (MTM) cover and gasket.


7. REMOVE EXTENSION HOUSING DUST(MTM) DEFLECTOR
  1. Using a brass bar and a hammer, remove the extension housing dust (MTM) deflector from the extension (MTM) housing sub-assembly.


8. REMOVE SHIFT LEVER SHAFT HOUSING SUB-ASSEMBLY

  1. C090700
    Remove the 6 bolts.

  1. D025940
    Using a plastic-faced hammer, remove the shift lever shaft housing sub-assembly.


9. REMOVE EXTENSION (MTM) HOUSING SUB-ASSEMBLY

  1. B085186
    Remove the 10 bolts.

  1. Using a plastic-faced hammer, remove the extension (MTM) housing sub-assembly.


10. REMOVE EXTENSION HOUSING OIL RECEIVER PIPE
  1. Remove the bolt and extension housing oil receiver pipe from the extension (MTM) housing sub-assembly.


11. REMOVE NO. 1 EXTENSION HOUSING OIL RECEIVER PIPE

  1. D029037
    Remove the No. 1 extension housing oil receiver pipe.


12. REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL

  1. D029043
    Using a screwdriver and hammer, remove the manual transmission extension housing oil seal from the extension (MTM) housing sub-assembly.


13. REMOVE FRONT BEARING RETAINER (MTM)

  1. D025950
    Remove the 8 bolts.

  1. D025951
    Using a brass bar and hammer, remove the front bearing retainer (MTM) from the manual transmission case.


14. REMOVE FRONT TRANSMISSION BEARING RETAINER OIL SEAL

  1. D025952E01
    Fix the front bearing retainer (MTM) in a vise in aluminum plate.

  1. Using SST, remove the front transmission bearing retainer oil seal.

    SST
    09308-00010  


15. REMOVE FRONT BEARING SHAFT SNAP RING

  1. D025953
    Using a snap ring expander, remove the front bearing shaft snap ring from the manual transmission case.


16. REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

  1. D025954
    Using a snap ring expander, remove the No. 1 counter gear front bearing snap ring from the manual transmission case.


17. REMOVE MANUAL TRANSMISSION CASE

  1. D029044
    Using a brass bar and hammer, remove the manual transmission case from the intermediate plate.


18. REMOVE TRANSMISSION MAGNET

  1. D025957
    Remove the transmission magnet from the intermediate plate.


19. FIX INTERMEDIATE PLATE

  1. C288143
    Fix the intermediate plate in a vise in between aluminum plates.


20. REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT

  1. D029046
    Using a T40 "TORX" socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.

  1. D025960
    Using a magnet hand, remove the compression spring and shift detent ball from the intermediate plate.

  1. C288144
    Using a T40 "TORX" socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.

  1. C288145
    Using a magnet hand, remove the 2 compression springs and 2 shift detent balls from the intermediate plate.


21. REMOVE SHIFT FORK SHAFT STOPPER

  1. D025963
    Using a 5 mm pin punch and hammer, remove the slotted spring pin from the No. 1 gear shift fork shaft.

  1. Remove the shift fork shaft stopper from the No. 1 gear shift fork shaft.


22. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

  1. C288146
    Using 2 screwdrivers and a hammer, remove the snap ring from the No. 1 gear shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C288147
    Remove the bolt from the No. 1 gear shift fork.

  1. C288148
    Remove the No. 1 gear shift fork shaft from the intermediate plate.

  1. D025967
    Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.


23. REMOVE SHIFT FORK SHAFT STOPPER

  1. D025969
    Using a 5 mm pin punch and a hammer, remove the slotted spring pin from the No. 2 gear shift fork shaft.

  1. Remove the shift fork shaft stopper from the No. 2 gear shift fork shaft.


24. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

  1. C288149
    Using 2 screwdrivers and a hammer, remove the snap ring from the No. 2 gear shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C262515
    Remove the bolt from the No. 2 gear shift fork.

  1. C288150
    Using a 5 mm pin punch and hammer, remove the slotted spring pin from the No. 2 gear shift fork shaft.

  1. C288151
    Remove the No. 2 gear shift fork shaft and No. 2 gear shift head.

  1. C288152
    Remove the No. 1 gear shift fork and No. 2 gear shift fork from the output shaft assembly.

  1. D025975
    Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


25. REMOVE REVERSE SHIFT FORK SHAFT

  1. D025976
    Using a 5 mm pin punch and hammer, remove the slotted spring pin from the reverse shift fork shaft.

  1. C288153
    Using a magnet hand, remove the straight pin from the reverse shift fork.

  1. C288154
    Using 2 screwdrivers and a hammer, remove the snap ring from the reverse shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C288155
    Remove the reverse shift fork shaft and No. 3 gear shift fork.


26. REMOVE REVERSE SHIFT FORK

  1. C290803
    Remove the reverse shift fork from the reverse shift arm.


27. REMOVE REVERSE SHIFT ARM BRACKET

  1. C291033
    Remove the torsion spring from the reverse shift arm bracket.

  1. C291034
    Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.

  1. C291035
    Using a screwdriver, pry out the snap ring from the reverse shift arm bracket.

  1. C291036
    Remove the reverse shift arm from the reverse shift arm bracket.


28. REMOVE SPEEDOMETER DRIVE (MTM) GEAR

  1. G034243
    Using snap ring expander, remove the snap ring.

  1. Remove the speedometer drive (MTM) gear and steel ball.

  1. Using a magnet hand, remove the steel ball.

  1. Using snap ring expander, remove the snap ring.


29. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

  1. C238817
    Using 2 screwdrivers and a hammer, remove the output shaft bearing shaft snap ring from the output shaft assembly.


30. REMOVE OUTPUT SHAFT REAR BEARING

  1. C268994E04
    Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft assembly.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


31. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE

  1. D025991
    Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.0039 to 0.0138 in.)


32. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE

  1. D025992
    Using a dial indicator, measure the radial clearance of the counter shaft 5th gear.

    Standard clearance:
    0.015 to 0.068 mm (0.0059 to 0.0027 in.)

    If the clearance is not within the specified values, replace the counter 5th gear bearing with a new one.


33. REMOVE COUNTER GEAR REAR SHAFT SNAP RING

  1. C272924
    Using 2 screwdrivers and a hammer, remove the counter gear rear shaft snap ring from the counter gear.


34. REMOVE NO. 3 TRANSMISSION HUB SLEEVE

  1. C272925
    Remove the No. 3 transmission hub sleeve from the counter shaft 5th gear.


35. REMOVE COUNTER SHAFT 5TH GEAR

  1. C272926E06
    Using SST, remove the counter shaft 5th gear together with the counter 5th gear bearing, 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, outer No. 3 synchronizer ring and No. 5 gear spline piece from the counter gear.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04021, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Turn
    *b
    Hold


36. REMOVE NO. 5 GEAR SPLINE PIECE

  1. C238819
    Remove the No. 5 gear spline piece from the counter shaft 5th gear.


37. REMOVE OUTER NO. 3 SYNCHRONIZER RING
  1. Remove the outer No. 3 synchronizer ring from the counter shaft 5th gear.


38. REMOVE COUNTER 5TH GEAR BEARING

  1. C089839
    Remove the counter 5th gear bearing from the counter shaft 5th gear.


39. REMOVE NO. 3 SYNCHROMESH SHIFTING KEY SPRING

  1. C247403
    Using a snap ring expander, remove the shaft snap ring.

  1. C250077
    Remove the No. 3 synchromesh shifting key spring and 2 No. 3 synchromesh shifting keys from the counter shaft 5th gear.


40. REMOVE 5TH GEAR THRUST WASHER

  1. C272928
    Remove the 5th gear thrust washer from the counter gear.


41. REMOVE 5TH GEAR THRUST WASHER PIN

  1. C272930
    Remove the 5th gear thrust washer pin from the counter gear.


42. REMOVE OUTPUT SHAFT REAR BEARING(MTM) RETAINER

  1. D026001
    Remove the 4 bolts and output shaft rear bearing (MTM) retainer from the intermediate plate.


43. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

  1. D026002E03
    Pull out the reverse idler gear shaft to the rear side and remove the reverse idler gear sub-assembly from the intermediate plate.


44. REMOVE COUNTER SHAFT CENTER BEARING

  1. C272932
    Using a snap ring expander, remove the snap ring.

  1. C272934E01
    Using SST, remove the counter shaft center bearing from the intermediate plate.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)

    HINT:
    Remove the bearing while tapping the tip of the counter gear so that the counter gear assembly is not pushed forward into the side wall of the output shaft assembly gear.


45. REMOVE COUNTER GEAR

  1. D026005
    Remove the counter gear from the intermediate plate.


46. REMOVE INPUT SHAFT ASSEMBLY

  1. D026006
    Remove the input shaft assembly and No. 2 synchronizer ring from the output shaft assembly.

    NOTICE:
    Do not drop the input shaft bearing and No. 2 synchronizer ring.


47. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

  1. C272936
    Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft assembly.


48. REMOVE OUTPUT SHAFT ASSEMBLY

  1. C272937
    Using a plastic-faced hammer, remove the output shaft assembly by tapping the intermediate plate.

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →