2014-2019 Hiace · Service Manual BRAKE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Oct 2014


SET REAR AXLE LOAD

  1. C102556

    HINT:
    If the vehicle unladen weight exceeds the specification, set it by following step 5.


    Rear axle load (including vehicle weight):
    Standard body type:
    Model
    Rear axle load kg (lb)
    ***202R (L) - *E****
    850 (1870)
    ***203R (L) - *E****
    850 (1870)
    Others
    900 (1980)
    Wide long body type:
    Model
    Rear axle load kg (lb)
    TRH213R - KDPNK
    1000 (2200)
    **H212R (L) - ******
    1050 (2310)
    **H213R (L) - ******
    1050 (2310)
    Wide super long body type:
    Model
    Rear axle load kg (lb)
    **H220R (L) - ******
    1050 (2310)
    **H221R (L) - ******
    1050 (2310)
    **H22*R - LEMD*N
    1150 (2530)
    **H22*R - LEMN*N
    1150 (2530)
    **H22*R - LEMD*T
    1150 (2530)
    **H22*R (L) - LEM*** (*1)
    1150 (2530)
    Others
    1000 (2200)

    *1: Except CHINA

INSTALL LSPV GAUGE (SST) AND BLEED AIR
SST
09709-29018  

  1. C102558

RAISE FRONT BRAKE PRESSURE 9,807 kPa (100 kgf/cm2, 1,422 psi) AND CHECK REAR BRAKE PRESSURE

  1. C102558
  2. HINT:
    Gradually depress on the brake pedal until the pressure reaches the specified valve. Do not overshoot the specified pressure. Read the value of rear pressure 2 seconds after adjusting to the specified fluid pressure.


    Rear brake fluid pressure table:
    Standard body type:
    Model
    Rear brake pressure
    ***202R (L) - *E****
    5860 +/-800 kPa
    (60 +/-8 kgf/cm2, 850 +/-116 psi)
    ***203R (L) - *E****
    5860 +/-800 kPa
    (60 +/-8 kgf/cm2, 850 +/-116 psi)
    Others
    5860 +/-800 kPa
    (60 +/-8 kgf/cm2, 850 +/-116 psi)
    Wide long body type:
    Model
    Rear brake pressure
    **H212R (L) - ******
    6600 +/-800kPa
    (67 +/-8 kgf/cm2, 957 +/-116 psi)
    **H213R (L) - ******
    6600 +/-800kPa
    (67 +/-8 kgf/cm2, 957 +/-116 psi)
    Wide super long body type:
    Model
    Rear brake pressure
    **H220R (L) - ******
    6600 +/-800 kPa
    (67 +/-8 kgf/cm2, 957 +/-116 psi)
    **H221R (L) - ******
    6600 +/-800 kPa
    (67 +/-8 kgf/cm2, 957 +/-116 psi)
    **H22*R - LEMD*N
    5500 +/-800 kPa
    (56 +/-8 kgf/cm2, 797 +/-116 psi)
    **H22*R - LEMN*N
    5500 +/-800 kPa
    (56 +/-8 kgf/cm2, 797 +/-116 psi)
    **H22*R - LEMD*T
    5500 +/-800 kPa
    (56 +/-8 kgf/cm2, 797 +/-116 psi)
    **H22*R (L) - LEM*** (*1)
    5500 +/-800 kPa
    (56 +/-8 kgf/cm2, 797 +/-116 psi)
    Others
    6600 +/-800 kPa
    (67 +/-8 kgf/cm2, 957 +/-116 psi)

    *1: Except CHINA

RAISE FRONT BRAKE PRESSURE 11,768 kPa (120 kgf/cm2, 1,707 psi) AND CHECK REAR BRAKE PRESSURE

Rear brake fluid pressure table:
Standard body type:
Model
Rear brake pressure
***202R (L) - *E****
6400 +/-1000 kPa
(65 +/-10 kgf/cm2, 928 +/-145 psi)
***203R (L) - *E****
6400 +/-1000 kPa
(65 +/-10 kgf/cm2, 928 +/-145 psi)
Others
6400 +/-1000 kPa
(65 +/-10 kgf/cm2, 928 +/-145 psi)
Wide long body type:
Model
Rear brake pressure
**H212R (L) - ******
7100 +/-1000 kPa
(72 +/-10 kgf/cm2, 1030 +/-145 psi)
**H213R (L) - ******
7100 +/-1000 kPa
(72 +/-10 kgf/cm2, 1030 +/-145 psi)
Wide super long body type:
Model
Rear brake pressure
**H220R (L) - ******
7100 +/-1000 kPa
(72 +/-10 kgf/cm2, 1030 +/-145 psi)
**H221R (L) - ******
7100 +/-1000 kPa
(72 +/-10 kgf/cm2, 1030 +/-145 psi)
**H22*R - LEMD*N
6000 +/-1000 kPa
(61 +/-10 kgf/cm2, 870 +/-145 psi)
**H22*R - LEMN*N
6000 +/-1000 kPa
(61 +/-10 kgf/cm2, 870 +/-145 psi)
**H22*R - LEMD*T
6000 +/-1000 kPa
(61 +/-10 kgf/cm2, 870 +/-145 psi)
**H22*R (L) - LEM*** (*1)
6000 +/-1000 kPa
(61 +/-10 kgf/cm2, 870 +/-145 psi)
Others
7100 +/-1000 kPa
(72 +/-10 kgf/cm2, 1030 +/-145 psi)

*1: Except CHINA

IF VEHICLE UNLADEN WEIGHT EXCEEDS SPECIFICATION, SET IT BY FOLLOWING STEPS

  1. B066592E01
    Make a graph of rear axle load and brake fluid pressure as shown in example 1 or 2, using the applicable data of ABC point data table.

  1. Input the rear axle load on the applicable graph and find out the fluid pressure crossover point.
    Example: When the rear axle load is 1200 kg (2646 lb), the fluid pressure crossover point is 6865 kPa (70 kgf/cm2, 996 psi).

  1. Calculate the rear brake pressure when the front brake pressure is 9807 kPa (100 kgf/cm2, 1422 psi) using the following formula.
    X: Fluid Pressure Crossover Point
    X + (100 - X) x 0.25
    Example:
    X: 6865 kPa (70 kgf/cm2, 996 psi)
    70 + (100 - 70) x 0.25= 77.5
    Rear brake pressure: 7600 kPa (77.5 kgf/cm2, 1102 psi)
    Service limit: +/- 800 kPa (8 kgf/cm2, 116 psi)

    C116334E01

    ABC point data table:
    Standard body type 
    Model
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    ***200R (L) - ******
    ***201R (L) - ******
    693
    (1528, 6.79)
    1000
    (10, 145)
    892
    (1967, 8.74)
    4500
    (46, 653)
    1470
    (3241, 14.41)
    9600
    (98, 1392)
    ***202R (L) - *D****
    ***203R (L) - *D****
    748
    (1649, 7.33)
    1000
    (10, 145)
    882
    (1945, 8.65)
    4400
    (45, 638)
    1405
    (3098, 13.77)
    9300
    (95, 1349)
    ***202R (L) - *E****
    ***203R (L) - *E****
    710
    (1565, 6.96)
    1000
    (10, 145)
    882
    (1945, 8.65)
    5300
    (54, 769)
    1640
    (3616, 16.07)
    11900
    (121, 1726)
    Wide long body type 
    Model
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    TRH213R - KDPNK
    801
    (1766, 7.85)
    2500
    (25, 363)
    -
    -
    1580
    (3483, 15.48)
    13700
    (140, 1987)
    **H212R (L) - ******
    **H213R (L) - ******
    781
    (1722, 7.65)
    2500
    (25, 363)
    882
    (1945, 8.65)
    4400
    (45, 638)
    1690
    (3726, 16.56)
    9900
    (101, 1436)
    Wide super long body type 
    Model
    Rear Spring Silencer
    A
    B
    C
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    kg (lb, kN)
    kPa (kg/cm2, psi)
    254mm Drum
    **H220R (L) - ******
    **H221R (L) - ******
    ALL
    760
    (1676, 7.44)
    2500
    (25, 363)
    935
    (2061, 9.16)
    4800
    (49, 696)
    1640
    (3616, 16.07)
    9500
    (97, 1378)
    **H222R (L) - ******
    **H223R (L) - ******
    for Type A
    for Type B (for Australia)
    837
    (1845, 8.20)
    2500
    (25, 363)
    995
    (2194, 9.76)
    5500
    (56, 798)
    1740
    (3836, 17.05)
    10400
    (106, 1508)
    for Type B (except Australia)
    786
    (1733, 7.71)
    2500
    (25, 363)
    1196
    (2637, 11.73)
    7800
    (79, 1131)
    1785
    (3935, 17.50)
    12300
    (125, 1784)
    TRH223L-LDPNK
    ALL
    801
    (1766, 7.86)
    2500
    (25, 363)
    -
    -
    1350
    (2976, 13.24)
    10800
    (111, 1566)
    295mm Drum
    **H222R (L) - ******
    **H223R (L) - ******
    for Type A
    889
    (1960, 8.72)
    1000
    (10, 145)
    996
    (2196, 9.77)
    3000
    (31, 435)
    1810
    (3990, 17.75)
    8600
    (87, 1247)
    for Type B
    936
    (2064, 9.18)
    1000
    (10, 145)
    1196
    (2637, 11.73)
    4600
    (47, 667)
    1810
    (3990, 17.75)
    9300
    (94, 1349)
    TRH223R - LEMDKN
    KDH222R - LEMDYN
    ALL
    891
    (1964, 8.74)
    1000
    (10, 145)
    1022
    (2253, 10.02)
    3300
    (34, 479)
    1825
    (4023, 17.90)
    8100
    (83, 1175)


    C297840E01
    Text in Illustration 
    *A
    Type A
    *B
    Type B


IF NECESSARY, ADJUST FLUID PRESSURE

  1. C102559E01
    Adjust the length of the shackle.
    Lower pressure - Lengthen "A"
    High pressure - Shorten "A"

    Initial set:
    120 mm (4.72 in.)

    Adjusting:
    112 to 128 mm (4.40 to 5.04 in.)

  1. C102561
    If the pressure cannot be adjusted by the shackle, raise or lower the valve body.
    Lower pressure - Lower
    High pressure - Raise

  1. Torque the nuts.

    Torque:
    12.5 N*m (130 kgf*cm, 9 ft.*lbf)

  1. Adjust the length of the shackle again.
    If it cannot be adjusted, inspect the valve body.


REMOVE LSPV GAUGE (SST) AND BLEED BRAKE SYSTEM
← COMPONENTS (from Oct 2014)REMOVAL (from Oct 2014) →