2014-2019 Hiace · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from Oct 2014


1. INSPECT COUNTER SHAFT 5TH GEAR RADIAL CLEARANCE

  1. C086503
    Install the 5th gear thrust washer lock ball, the 5th gear thrust washer, and the 5th gear to the counter gear.

  1. Using a dial indicator, measure the counter shaft 5th gear radial clearance.

    Standard clearance:
    0.008 to 0.034 mm(0.0003 to 0.00134 in.)

    If the clearance is not as specified, replace the 5th gear bearing.


2. REMOVE COUNTER 5TH GEAR BEARING

  1. D033580
    Remove the 5th gear bearing from the 5th gear.


3. REMOVE TRANSMISSION HUB SLEEVE NO.3

  1. D033581
    Using a snap ring expander, remove the snap ring from the 5th gear.

  1. D033572
    Remove the hub sleeve No.3, 2 synchromesh shifting keys No.3, key spring (return spring), and key spring (C spring) from the 5th gear.


4. INSPECT SYNCHRONIZER RING NO.3

  1. D033573
    Apply gear oil to the gear spline piece No.5 cone. Press the synchronizer ring against the gear spline piece No.5 cone and check that the synchronizer ring does not turn in the directions shown in the illustration.
    If it turns, replace the synchronizer ring.

  1. D033574
    Using a feeler gauge, measure the clearance between the synchronizer ring No.3 back and gear spline piece No.5 spline end.

    Standard clearance:
    0.65 to 1.35 mm (0.0256 to 0.0531 in.)

    If the clearance is not as specified, replace the synchronizer ring No.3.

    NOTICE:
    Ensure the fine lapping compound is completely washed off after rubbing.


5. INSPECT TRANSMISSION HUB SLEEVE NO.3

  1. D033575
    Check the sliding condition between the transmission hub sleeve No.3 and counter shaft 5th gear.

  1. Check that the spline gear's edges of the transmission hub sleeve No.3 are not worn down.

  1. D033576E02
    Using vernier calipers, measure the width of the transmission hub sleeve No.3 groove and the thickness of the claw part on the gear shift fork No.3, and calculate the clearance.

    Standard clearance (A - B):
    0.25 to 0.45 mm (0.0098 to 0.0177 in.)

    If the clearance is not as specified, replace the transmission hub sleeve No.3 and gear shift fork No.3.


6. INSPECT COUNTER SHAFT 5TH GEAR

  1. D033577
    Using a cylinder gauge, measure the inside diameter of the 5th gear.

    Standard inside diameter:
    33.015 to 33.040 mm (1.2998 to 1.3008 in.)

    Maximum inside diameter:
    33.040 mm (1.3008 in.)

    If the inside diameter exceeds the maximum, replace the 5th gear.


7. INSPECT COUNTER GEAR

  1. C086509
    Using a micrometer, measure the outside diameter of the journal surface.

    Standard outside diameter:
    25.984 to 26.000 mm (1.0230 to 1.0236 in.)

    Minimum out side diameter:
    25.984 mm (1.0230 in.)

    If the outside diameter is less than the minimum, replace the counter gear.


8. INSPECT COUNTER GEAR FRONT BEARING OR ROLLER

  1. C086510
    Make sure the front bearing rotates smoothly.
    If the bearing does not rotate smoothly, replace the bearing.


9. REMOVE COUNTER GEAR FRONT BEARING OR ROLLER

  1. C086511
    Using a snap ring expander, remove the counter gear front bearing snap ring No.2 from the counter gear.

  1. C086512E01
    Using SST, a press, and a socket wrench 14 mm, remove the counter gear front bearing from the counter gear.
    SST
    09950-00020  

← COMPONENTS (from Oct 2014)INSPECTION (from Oct 2014) →