2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Oct 2014 – Nov 2015


INSPECT STARTER

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter in a vise between aluminum plates.

  1. Perform pull-in test.

    1. A146228E02
      Remove the nut and disconnect the lead wire from terminal C.
      Text in Illustration 
      *1
      Terminal C

    2. A222481E01
      Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Perform a holding test.

    1. A222482E01
      When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
      Text in Illustration 
      *1
      Terminal C
      If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Inspect the clutch pinion gear return.

    1. A222483
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Perform an operation test without load.

    1. Connect the lead wire to terminal C with the nut.

      Torque:
      24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    2. A282947E01
      Connect the battery and an ammeter to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30

    3. Check that the starter rotates smoothly and steadily while the pinion gear extended. Then measure the current.

      Standard current:
      220 A or less at 11.0 V

      If the result is not as specified, inspect the starter assembly

      HINT:
      Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A146237E02
    Check the pull-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the result is not as specified, replace the magnet starter switch assembly.

  1. A146238E02
    Check the hold-in coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Starter switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT BRUSH

A102612
  1. Using a vernier caliper, measure the brush length.

    Standard length:
    21.0 mm (0.828 in.)

    Minimum length:
    12.0 mm (0.472 in.)

    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A146236
    Inspect the brush insulation.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush holder - Negative (-) brush holder
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter brush holder assembly.

  1. A102613
    Take a pull scale reading the instant the brush spring separates from the brush.

    Standard spring load:
    26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf)

    Minimum spring load:
    12 N (1 kgf,2.8 lbf)

    If the spring load is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. A146234
    Inspect the field coil for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C - Brush
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. A146235
    Inspect the field coil for ground.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C - Starter yoke body
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, restore the surface with sandpaper (No. 400) or on a lathe. If necessary, replace the starter armature assembly.

  1. A146232E02
    Inspect the commutator for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. A146233E02
    Inspect the commutator for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Coil Core
      *2
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. A150703
    Inspect the commutator for circle runout.

    1. Place the armature on V-blocks.

    2. Using a dial gauge, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the circle runout is more than the maximum, replace the starter armature assembly.

  1. A102608
    Using a vernier caliper, measure the commutator diameter.

    Standard commutator diameter:
    43.0 mm (1.69 in.)

    Minimum commutator diameter:
    42.0 mm (1.65 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. A102609
    Using a vernier caliper, measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, replace the starter armature assembly.

  1. Inspect the bearings.

    1. Check that the bearings rotate smoothly.
      If the result is not as specified, replace the starter armature assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A115056
    Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter clutch.

  1. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
    If the result is not as specified, replace the starter clutch.

← DISASSEMBLY (Oct 2014 – Nov 2015)REASSEMBLY (Oct 2014 – Nov 2015) →