2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


INSPECT STARTER ASSEMBLY (for 1.6 kW Type)

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform pull-in test.

    1. G037637E03
      Remove the nut, disconnect the field coil lead wire from terminal C.
      Text in Illustration 
      *1
      Terminal C

    2. G037638E03
      Connect the battery to the magnetic switch as shown in the illustration. Check that the clutch pinion gear is extended.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50

  1. Perform holding test.

    1. G037639E03
      Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50

  1. Check the return operation.

    1. G037640E03
      Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      *1
      Terminal 50

  1. Perform operation test without load.

    1. Connect the field coil lead wire to terminal C.

      Torque:
      10 N*m{ 102 kgf*cm , 7.4 ft.*lbf }

  1. Mount the starter in a vise between aluminum plates.

  1. G037641E03
    Connect the battery and ammeter to the starter as shown in the illustration.
    Text in Illustration 
    *1
    Terminal 30
    *2
    Terminal 50
    *3
    Ammeter

  1. Check that the ammeter indicates the specified current.

    Specified current:
    90 A or less at 11.5 V


INSPECT STARTER ASSEMBLY (for 1.7 kW Type)

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Perform pull-in test.

    1. Remove the nut, and then disconnect the lead wire from terminal C.

    2. A122416E02
      Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear move outward. If the clutch pinion gear does not move, replace the magnet starter switch.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C

  1. Perform holding test.

    1. A122417E02
      When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear returns out.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the clutch pinion gear returns inward, replace the magnet starter switch.

  1. Inspect clutch pinion gear return.

    1. A122418E02
      Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      *1
      Terminal 50
      If the clutch pinion gear does not return inward, replace the magnet starter switch.

  1. Perform operation test without load.

    1. Connect the lead wire to terminal C.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Mount the starter in a vise between aluminum plates.

    3. A122419E02
      Connect the battery and an ammeter to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 30
      *2
      Terminal 50

    4. Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

      Standard current:
      90 A or less at 10.9 V

      If the result is not as specified, replace the starter assembly.


INSPECT STARTER ASSEMBLY (for 2.0 kW Type)

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter in a vise between aluminum plates.

  1. Perform pull-in test.

    1. Remove the nut, and then disconnect the lead wire from terminal C.

    2. A220449E01
      Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. A220450E01
    Perform holding test.

    1. Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains extended.

      Text in Illustration 
      *1
      Terminal C
      If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. A220451
    Inspect the clutch pinion gear return.

    1. Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
      If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.

  1. Perform operation test without load.

    1. Connect the lead wire to terminal C.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. A224837E01
      Connect the battery and an ammeter to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30

    3. Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

      Specified Current:
      100 A or less at 11.5 V

      If the result is not as specified, inspect the starter assembly.

      HINT:
      Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.

← SYSTEM DIAGRAM (from Oct 2014)INSPECTION (from Jan 2015) →