2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT STARTER ARMATURE ASSEMBLY

  1. A112475E02
    Check the commutator for an open circuit.

    1. Using an ohmmeter, check that there is continuity between the segments of the commutator.

      1. If there is no continuity between any segment, replace the armature assembly.

  1. A112476E01
    Check the commutator for a short circuit.

    1. Using an ohmmeter, check the resistance between the commutator and armature core.

      Standard:
      10 MΩ or higher

      1. If the result is not as specified, replace the armature assembly.

  1. A102632
    Check the commutator circle runout.

    1. Place the armature on the V-blocks.

    2. Using a dial gauge, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.0020 in.)

      1. If the circle runout is greater than maximum, replace the armature assembly.

  1. A112478
    Using vernier calipers, measure the commutator diameter.

    Standard diameter:
    36.0 mm (1.417 in.)

    Minimum diameter:
    35.0 mm (1.378 in.)

    1. If the diameter is less than the minimum, replace the armature assembly.

  1. ST00040
    Measure the undercut depth of the commutator.

    Standard depth:
    0.7 mm (0.028 in.)

    Minimum depth:
    0.2 mm (0.008 in.)

    1. If the undercut depth is less than the minimum, correct it with a hacksaw blade.

  1. Inspect the bearings.

    1. Check that the bearing rotates smoothly.

      1. If necessary, replace them.


INSPECT STARTER YOKE ASSEMBLY

  1. A112479
    Inspect for an open circuit.

    1. Check that there is continuity between the terminal C wire and brushes.

      1. If there is no continuity, replace the starter yoke assembly.

  1. A112480
    Inspect for a short circuit.

    1. Check the continuity between the terminal C wire and starter yoke body.

    2. Check the continuity between the brushes and starter yoke body.

      Standard:
      10 MΩ or higher

      1. If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH

  1. A112481E03
    Using vernier calipers, measure the brush length.

    Standard brush length:
    20.5 mm (0.807 in.)

    Minimum brush length:
    11.0 mm (0.433 in.)

    1. If the length is less than the minimum, replace the brush holder and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. A112482
    Using an ohmmeter, check the continuity between the positive and negative brush holders.

    Standard:
    10 MΩor higher

    1. If the result is not as specified, replace the brush holder assembly.

  1. ST00019
    Using a pull scale, measure the brush spring load.

    Standard spring load:
    26 to 45 N (2.7 to 4.6 kgf, 5.8 to 10.1 lbf)

    Minimum spring lord:
    12.4 N (1.3 kgf, 2.8 lbf)

    1. If the spring load is less than the minimum, replace the brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A112483E01
    Check that the starter clutch operates.
    1. If the starter clutch does not operate, replace it.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. A112485E03
    Check the pull-in coil resistance.

    1. Using an ohmmeter, check that there is continuity between terminals 50 and C.

      1. If there is no continuity, replace the magnet starter switch assembly.

  1. A112484E03
    Check the holding coil resistance.

    1. Using an ohmmeter, check that there is continuity between terminals 50 and switch body.

      1. If there is no continuity, replace the magnet starter switch assembly.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →