2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. Inspect the pull-in coil.

    1. G036853E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

  1. Inspect the holding coil.

    1. G036854E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Switch Body
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.


INSPECT BRUSH

  1. A062430E10
    Using a vernier caliper, measure the brush length.

    Standard brush length:
    15.0 mm (0.591 in.)

    Minimum brush length:
    9.0 mm (0.354 in.)

    Text in Illustration 
    *1
    Length
    *a
    Brush Holder Side
    *b
    Starter Yoke Side
    If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Inspect the insulation.

    1. G036824E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush holder - Negative (-) brush holder
      Always
      10 kΩ or higher

      If the result is not as specified, repair or replace the starter brush holder assembly.

  1. Check the brush spring load.

    1. ST00019E11
      Take a pull scale reading as soon as the brush spring separates from the brush.

      Standard spring load:
      22 to 28 N (2 to 3 kgf, 4.8 to 6.2 lbf)

      Minimum spring load:
      12 N (1 kgf, 2.8 lbf)

      Text in Illustration 
      *1
      Brush Spring
      *2
      Brush
      If the spring load is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. Inspect the field coil for an open circuit.

    1. A074964E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Lead wire - Brush
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

    2. A076125E03
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal A -Terminal B
      20°C (68°F)
      1.5 to 1.9 Ω

      Text in Illustration 
      *1
      Terminal A
      *2
      Terminal B
      If the result is not as specified, replace the starter yoke assembly.


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.

  1. Inspect the commutator for an open circuit.

    1. G036820E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator for a short circuit.

    1. G036821E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Armature core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Armature Core
      If the result is not as specified, replace the starter armature assembly.

  1. Check the commutator circle runout.

    1. P010586E01
      Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the circle runout is more than the maximum, replace the starter armature assembly.

  1. Check the commutator diameter.

    1. P010587E01
      Using a vernier caliper, measure the commutator diameter.

      Standard commutator diameter:
      35.0 mm (1.38 in.)

      Minimum commutator diameter:
      34.0 mm (1.34 in.)

      If the diameter is less than the minimum, replace the starter armature assembly.

  1. ST00040E01
    Check the undercut depth.

    1. Using a vernier caliper, measure the undercut depth of the commutator.

      Standard undercut depth:
      0.7 mm (0.0276 in.)

      Minimum undercut depth:
      0.2 mm (0.00787 in.)

      If the undercut depth is less than the minimum, replace the starter armature assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY

  1. A223418
    Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter clutch sub-assembly.

  1. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
    If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →