2014-2019 Hiace · Service Manual ENGINE

P0101 Mass Air Flow Circuit Range / Performance Problem

Diagnostic trouble codes · Vehicles built Jan 2015 – Nov 2015

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

Refer to DTC P0102 (Click here).
P0101 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
After warming up engine, idle engine for 20 seconds, and then maintain engine at 3000 rpm for 20 seconds
After the engine is warmed up, condition (a) continues for more than 10 seconds when idling (2 trip detection logic):
(a) Mass air flow meter output is higher than 4.4 V.
  1. Air induction system
  2. Mass air flow meter
Conditions (a) and (b) continue for more than 10 seconds with the engine speed at 1250 rpm or more (2 trip detection logic):
(a) VTA is higher than 0.1 V.
(b) Mass air flow meter output is below 0.7 V.
Related Data List 
DTC No.
Data List
P0101
  1. MAF
  2. Actual EGR Valve Pos.
  3. Actual Throttle position

HINT:
  1. If DTC P0101 is stored due to the mass air flow meter output voltage being too low, the ECU mistakenly determines that there is less air than the actual intake air amount and EGR is decreased to match the target EGR. As a result, the following symptom may appear:
    1. Combustion noise worsens
  2. If DTC P0101 is stored due to the MAF meter output voltage being too high, the ECU mistakenly determines that there is more air than the actual intake air amount and EGR is increased to match the target EGR. As a result, the following symptoms may appear:
    1. Misfire
    2. White smoke
    3. Black smoke


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0101)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0101 and other DTCs are output
    A
    P0101 is output
    B

    HINT:
    If codes other than P0101 are output, perform troubleshooting for those DTCs first.



A
GO TO DTC CHART (Click here)
B


2. CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage (Click here).

    OK:
    No leakage from air induction system.



NG
Go to step 4
OK


3. REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).



NEXT
Go to step 5
4. REPAIR OR REPLACE AIR INDUCTION SYSTEM
  1. Repair or replace the air induction system.


NEXT


5. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. After warming up the engine, idle the engine for 20 seconds, and then maintain the engine at 3000 rpm for 20 seconds.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0101.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, maintain the engine at 3000 rpm for 30 seconds, and then idle the engine for 5 minutes.


NEXT

END


← P0101 Mass Air Flow Circuit Range / Performance Problem (Oct 2014 – Dec 2014)P0101 Mass Air Flow Circuit Range / Performance Problem (Dec 2015 – Mar 2016) →