ON-VEHICLE INSPECTION
Inspection · Vehicles built from Oct 2014
| CHECK INTAKE MANIFOLD (w/o DPF) |
Using a 3-way connector, connect a vacuum gauge between the control valve and VSV.

Warm up the engine.
Measure the vacuum.
- Standard Vacuum:
Engine Condition
VSV Condition
Specified Condition
Idling
ON
Approx. 35 kPa (263 mmHg, 10.3 in.Hg)
3000 rpm or higher
OFF
0 kPa (0 mmHg, 0 in.Hg)
| CHECK INTAKE AIR CONTROL SYSTEM |
Check for leakage or clogging between the air cleaner housing and turbocharger inlet, and between the turbocharger outlet and cylinder head.
Condition
Operation
Clogged air cleaner
Clean or replace
Collapsed or deformed hoses
Repair or replace
Leakage from connections
Check each connection and repair
Cracks in components
Check and replace
| CHECK EXHAUST SYSTEM |
Check for leakage or clogging between the cylinder head and turbocharger inlet, and between the turbocharger outlet and exhaust pipe.
Condition
Operation
Deformed components
Repair or replace
Foreign matter in passages
Remove
Leakage from components
Repair or replace
Cracks in components
Check and replace
| CHECK BOOST PRESSURE |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Warm up the engine.
- HINT:
- Be sure to perform the inspection when the engine coolant temperature is between 75 to 90°C (167 to 194°F).
Using a 3-way connector, connect SST (turbocharger pressure gauge) between the diesel turbo pressure sensor (manifold absolute pressure sensor) and the gas filter.

- SST
- 09992-00242
Fully apply the parking brake and chock the 4 wheels.
w/ DPF:
for Manual Transmission:
While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).- Standard Pressure (Gauge Pressure):
- 5 to 35 kPa (0.05 to 0.35 kgf/cm2, 0.72 to 5.0 psi)
for Automatic Transmission:
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4600 rpm).- Standard Pressure (Gauge Pressure):
- 5 to 35 kPa (0.05 to 0.35 kgf/cm2, 0.72 to 5.0 psi)
- The intake system or exhaust system has leakage or blockage.
- The turbocharger sub-assembly is malfunctioning.
- The EGR valve does not close.
- The diesel throttle body does not open.
- The vacuum hose connected to the diesel turbo pressure sensor (manifold absolute pressure sensor) is cracked or disconnected.
- The mass air flow meter is malfunctioning.
- A fuel injector is malfunctioning.
w/o DPF:
for Manual Transmission:
While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4450 rpm).- Standard Pressure (Gauge Pressure):
- 10 to 40 kPa (0.10 to 0.41 kgf/cm2, 1.4 to 5.8 psi)
for Automatic Transmission:
Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (approximately 4450 rpm).- Standard Pressure (Gauge Pressure):
- 10 to 40 kPa (0.10 to 0.41 kgf/cm2, 1.4 to 5.8 psi)
- The intake system or exhaust system has leakage or blockage.
- The turbocharger sub-assembly is malfunctioning.
- The EGR valve does not close.
- The diesel throttle body does not open.
- The vacuum hose connected to the diesel turbo pressure sensor (manifold absolute pressure sensor) is cracked or disconnected.
- The mass air flow meter is malfunctioning.
- A fuel injector is malfunctioning.
Chart showing the suspected trouble areas when the pressure is lower than the standard.
- HINT:
- ○: If a problem listed in the leftmost column of the chart exists, or if a part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".
- The values in the chart are applicable when the engine coolant temperature is between 75 to 90°C (167 to 194°F).
- The values in the chart are for vehicles equipped with a manual transmission. For vehicles with an automatic transmission, use these values as a reference only as they may differ from the actual values.
- The values in the chart are valid in areas with an absolute atmospheric pressure higher than 95 kPa. Standard atmospheric pressure is 101 kPa. Atmospheric pressure decreases by 1 kPa for every 100 m increase in altitude, and is also affected by the current weather conditions.
- When the altitude increases, atmospheric pressure and MAP decrease.
- ○: If a problem listed in the leftmost column of the chart exists, or if a part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".
Item
MAP
(Absolute pressure inside intake manifold)
MAF
(Intake air flow rate)
Accel Position
Actual Throttle Position
Actual EGR Valve Position
EGR Close Lrn. Status
(EGR valve fully closed position learning status)
Fuel Pressure
Injection Feedback Val #1 (to #4)
Values taken from an actual normal vehicle
*1
-
115 to 150 g/sec.
99% or more
0%
0%
OK
-
-3 to +3 mm3/st
Values which represent a malfunction
*1
None
MAF is less than 115 g/sec.
Accel Position is not fully depressed position
*2
Actual Throttle Position is not fully open position
Actual EGR Valve Position is not 0%
NG
(Determined after performing learning)
Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady)
Outside of above range
Turbocharger
○
○
-
-
-
-
-
-
EGR valve does not close or has problem with movement
○
○
-
-
○
(Problem with EGR valve movement)
*3
○
(EGR valve does not close)
*3
-
-
Problem with diesel throttle movement
○
(Intake airflow decreases)
○
-
○
-
-
-
-
Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists
-
○
○
-
-
-
-
-
Intake air system leakage or blockage
○
○
-
-
-
-
-
-
Exhaust gas leakage before turbocharger or blockage
○
○
-
-
-
-
-
-
Manifold absolute pressure sensor
○
○
-
-
-
-
-
-
Manifold absolute pressure sensor hose is disconnected
○
○
-
-
-
-
-
-
Mass air flow meter sub-assembly
-
○
-
-
-
-
-
-
Fuel system (injector, supply pump or common rail)
○
○
-
-
-
-
○
(Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
○
*4
- HINT:
- *1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.
- *2: The Accel Position is the accelerator opening angle (%) for engine control use. The value indicates around 100% when the accelerator pedal is fully depressed. If the value does not indicate around 100% when the accelerator pedal is fully depressed, the accelerator pedal position sensor circuit or the pedal itself is malfunctioning. When the MIL is illuminated, even with the accelerator pedal fully depressed and an Accel Position of below 70%, it means the fail-safe is restricting the accelerator.
- *3: DTC P0400, P2BAB or P2BAC may be stored at this time. If the actual EGR valve position follows the target EGR valve position slowly, a feeling of hesitation may occur.
- *4: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder may have a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st because these values are injection volume correction values calculated by the ECM during engine idling and not correction values for the high engine load condition related to boost pressure control and engine output performance.
- *1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.
| CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR |
Check the terminal voltage.
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
D51-3 (VC) - D51-1 (E)
Ignition switch ON
4.75 to 5.25 V
D51-2 (PIM) - D51-1 (E)
Ignition switch ON
3.0 to 5.0 V
If the result is not as specified, there is an open or short in VC or E circuit.Text in Illustration *a
Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
Check the intake manifold pressure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the values displayed on the GTS.
- OK:
- Equivalent to atmospheric pressure.
- HINT:
- Standard atmospheric pressure is 101 kPa (abs) [758 mmHg (abs)].
- For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.
- Standard atmospheric pressure is 101 kPa (abs) [758 mmHg (abs)].
| CHECK MOTOR FOR TURBOCHARGER CONTROL |
- CAUTION:
- Wear protective gloves to prevent injuries and burns when checking the turbocharger.
- The engine compartment becomes hot when the engine is running.
- Wear protective gloves to prevent injuries and burns when checking the turbocharger.
Remove the No. 1 exhaust manifold heat insulator (Click here) and No. 1 turbo insulator (Click here).
Make sure that the connector is properly connected.
Turn the ignition switch from ON to off.
w/ DPF:
Check the DC motor's operation. Check that the motor rod stroke is as shown in A to C in the illustration below.
After the DC motor operates, visually check that the vane activation link contacts the fully closed stopper.


- NOTICE:
- Never loosen or tighten the lock nut of the fully closed stopper.
w/o DPF:
Check the DC motor's operation. Check that the motor rod stroke is as shown in A to D in the illustration below.
After the DC motor operates, visually check that the vane activation link contacts the fully closed stopper.
- NOTICE:
- Never loosen or tighten the lock nut of the fully closed stopper.
-


