2014-2019 Hiace · Service Manual ENGINE

P0112 Intake Air Temperature Circuit Low Input

Diagnostic trouble codes · Vehicles built Jan 2015 – Mar 2016

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The intake air temperature sensor is detects the intake air temperature.
A thermistor built into the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
A208462E01
P0112 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Short in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor
  3. ECM
P0113 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor
  3. ECM
Related Data List 
DTC No.
Data List
P0112
Intake Air
P0113

HINT:
  1. If DTC P0112 and/or P0113 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power
  2. When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
    Reference 
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit


WIRING DIAGRAM

A210074E73

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    Same as actual intake air temperature

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    OK (same as actual intake air temperature)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or higher.



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

  1. A099845E10
    Disconnect the intake air temperature sensor connector.

  1. Connect terminals 1 and 2 of the intake air temperature sensor wire harness side connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Intake air temperature sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to intake air temperature sensor)

  1. Reconnect the intake air temperature sensor connector.



OK
Go to step 7

NG
Go to step 3
3. CHECK INTAKE AIR TEMPERATURE SENSOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
  1. Disconnect the intake air temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-2 - D105-110 (THA)
    Always
    Below 1 Ω
    A2-1 - D105-87 (ETHB)
    Always
    Below 1 Ω

  1. Reconnect the intake air temperature sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

  1. A198733E38
    Disconnect the intake air temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Intake air temperature sensor
    *2
    ECM

  1. Reconnect the intake air temperature sensor connector.



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
  1. Disconnect the intake air temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A2-2 or D105-110 (THA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the intake air temperature sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR
  1. Replace the intake air temperature sensor (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE INTAKE AIR TEMPERATURE SENSOR
  1. Replace the intake air temperature sensor (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0112 Intake Air Temperature Circuit Low Input (+ P0113) (Oct 2014 – Dec 2014)P0112 Intake Air Temperature Circuit Low Input (+ P0113) (Apr 2016 – Dec 2016) →