P0627 Fuel Pump Control Circuit / Open
Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 1 second |
Even though the CPU (command area inside the ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic). |
|
| DTC No. |
Data List |
| P0627 |
|
- HINT:
- For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here).
- When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Common Rail Pressure.
Under a stable operating condition such as idling, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.
- For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (Click here).
WIRING DIAGRAM
Refer to DTC P0088 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT SUCTION CONTROL VALVE |
Disconnect the suction control valve connector.

Text in Illustration *1
Fuel Supply Pump Assembly
*2
Suction Control Valve
Measure the resistance of the suction control valve.
- OK:
- No open or short circuit malfunction.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
Disconnect the suction control valve connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D47-1 - D99-41 (PCV+)
Always
Below 1 Ω
D47-2 - D99-81 (PCV-)
Always
Below 1 Ω
D47-1 or D99-41 (PCV+) - Body ground
Always
10 kΩ or higher
D47-2 or D99-81 (PCV-) - Body ground
Always
10 kΩ or higher
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (Click here).
Start the engine and idle it for 1 second or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result Result
Proceed to
No DTC is output
A
P0627 is output
B
|
|
||||
| A | ||
| ||
| 4. REPLACE SUCTION CONTROL VALVE |
Replace the suction control valve (Click here).
| NEXT | |
| 5. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 6. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
|
|
||||
| 7. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 1 second or more.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
