2014-2019 Hiace · Service Manual ENGINE

P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance

Diagnostic trouble codes · Vehicles built Apr 2016 – Dec 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to the opening and closing of the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.
P0488 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Perform the following repeatedly for 1 minute: gradually raise the engine speed to 3000 rpm from idling over approximately 10 seconds, and then release the accelerator pedal to return to an idling state.
The throttle motor activation duty is more than a specified value for 30 seconds (1 trip detection logic).
  1. Throttle valve stuck
  2. Throttle valve does not move smoothly
  3. Open or short in throttle control motor circuit
  4. ECM
Related Data List 
DTC No.
Data List
P0488
  1. Throttle Motor Duty
  2. Actual Throttle Position
Reference 
Condition
Throttle Valve Position
Moment when accelerator pedal is depressed further or released at 3000 rpm
Throttle valve opening angle varies smoothly

MONITOR DESCRIPTION

The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly. The ECM will determine that the throttle valve is malfunctioning and illuminate the MIL.
A128641E10

WIRING DIAGRAM

A319498E03

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Although the DTC titles say exhaust gas recirculation throttle position control Range / Performance, these DTCs relate to the throttle valve
  2. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR POWER SOURCE)

  1. A129055E14
    Disconnect the throttle control motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D48-2 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Throttle Control Motor)

  1. Reconnect the throttle control motor connector.



NG
Go to step 7
OK


2. CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
  1. Disconnect the throttle control motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D48-3 (RSC) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the throttle control motor connector.



NG
Go to step 8
OK


3. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM)
  1. Disconnect the throttle control motor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D48-1 (RSO) - D98-78 (LUSL)
    Always
    Below 1 Ω
    D48-1 (RSO) or D98-78 (LUSL) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle control motor connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


4. REPLACE DIESEL THROTTLE BODY ASSEMBLY
  1. Replace the diesel throttle body assembly (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0488)
  1. Clear the DTCs (Click here).

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Start the engine.

  1. Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm and lower it.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0488 is output
    A
    No DTC is output
    B



B
Go to step 9
A


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 9
7. REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE CONTROL MOTOR - BATTERY)
  1. Repair or replace the harness or connector.



NEXT
Go to step 9
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm, and then lower it.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0488.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, over a period of 10 seconds or more, slowly raise the engine speed to 3000 rpm again, and then idle the engine for 5 minutes.


NEXT

END


← P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (Dec 2015 – Mar 2016)P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (from Jan 2017) →