2014-2019 Hiace · Service Manual ENGINE

P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built from Jan 2017

Also covers:

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

HINT:
  1. For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (Click here).
  2. If P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system (Click here).
  3. These DTCs are recorded when the air fuel ratio sensor has a malfunction, although the title is the oxygen sensor.

The air fuel ratio sensor has the characteristic of providing output voltage which is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage* is used by the ECM to control the air-fuel ratio.
The air fuel ratio sensor is located after the DPF catalytic converter. This sensor has been developed based on the structure and technology of a sensor that is being used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with DPF in order to eliminate the influence of the sensor temperature and particulate matter (PM).
In order to reduce both PM, the ECM adjusts the air-fuel ratio to slightly rich (but it is lean compared with the stoichiometric air-fuel ratio) based on signals from the air fuel ratio sensor. When the ECM performs PM forced regeneration by adding fuel using the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted using the sensor.
*: The voltage value changes inside the ECM only.
A264921E02

HINT:
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A210271E12
P2237 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
  1. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
  2. Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS.
When either of the following conditions is met.
  1. Air fuel ratio sensor circuit malfunction
  2. The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.
  3. 1 trip detection logic (EOBD (Euro OBD)*)
  4. 2 trip detection logic (Not OBD compliant*)
Main trouble area: Open in air fuel ratio sensor circuit
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2238 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 7 seconds
Air fuel ratio sensor circuit low (bank 1 sensor 1)
  1. 1 trip detection logic (EOBD (Euro OBD)*)
  2. 2 trip detection logic (Not OBD compliant*)
Main trouble area: Open in air fuel ratio sensor circuit
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2239 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 7 seconds
Air fuel ratio sensor circuit high (bank 1 sensor 1)
  1. 1 trip detection logic (EOBD (Euro OBD)*)
  2. 2 trip detection logic (Not OBD compliant*)
Main trouble area: Short in air fuel ratio sensor circuit
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2252 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 7 seconds
Air fuel ratio sensor circuit low (bank 1 sensor 1)
  1. 1 trip detection logic (EOBD (Euro OBD)*)
  2. 2 trip detection logic (Not OBD compliant*)
Main trouble area: Open in air fuel ratio sensor circuit
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
P2253 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 7 seconds
Air fuel ratio sensor circuit high (bank 1 sensor 1)
  1. 1 trip detection logic (EOBD (Euro OBD)*)
  2. 2 trip detection logic (Not OBD compliant*)
Main trouble area: Short in air fuel ratio sensor circuit
  1. Open or short in air fuel ratio sensor circuit
  2. Air fuel ratio sensor
  3. ECM
*: Check the "OBD Requirements" in the Data List.
Related Data List 
DTC No.
Data List
P2237
  1. AFS Voltage B1S1
  2. Exhaust Temperature B1S1
P2238
P2239
P2252
P2253

MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

WIRING DIAGRAM

Refer to DTC P0031 (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    r4-3 (AF2+) - D99-125 (AF2+)
    Always
    Below 1 Ω
    r4-4 (AF2-) - D99-126 (AF2-)
    Always
    Below 1 Ω
    r4-3 (AF2+) or D99-125 (AF2+) - Body ground
    Always
    10 kΩ or higher
    r4-4 (AF2-) or D99-126 (AF2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 5
OK


2. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


3. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Warm up the engine.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

    HINT:
    Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.

  1. Confirm that the DTC is not output again.



NG
Go to step 4
OK

END

4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 6
5. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Warm up the engine.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

    HINT:
    Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (for A/F sensor) (Bank 1 Sensor 1) (+ P2238, P2239, P2252, P2253) (Apr 2016 – Dec 2016)P244A Diesel Particulate Filter Differential Pressure Too Low (+ P244C, P2463) (Oct 2014 – Dec 2014) →