2014-2019 Hiace · Service Manual ENGINE

VC Output Circuit

Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the throttle position sensor (throttle body assembly), EGR valve position sensor (electric EGR control valve assembly), manifold absolute pressure sensor, accelerator pedal position sensor (accelerator pedal rod assembly) and fuel pressure sensor.

WIRING DIAGRAM

A319604E01
A319605E01

INSPECTION PROCEDURE


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    OK:
    MIL lights up



OK
SYSTEM OK
NG


2. CHECK CONNECTION BETWEEN GTS AND ECM
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Check the communication between the GTS and ECM.

    Result 
    Result
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3. CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the throttle position sensor connector.



B
REPLACE DIESEL THROTTLE BODY ASSEMBLY
A


4. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the manifold absolute pressure sensor connector.



B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
A


5. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the accelerator position sensor connector.



B
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
A


6. CHECK MIL (EGR VALVE POSITION SENSOR)
  1. Disconnect the EGR valve position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the EGR valve position sensor connector.



B
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
A


7. CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the fuel pressure sensor connector.



B
REPLACE COMMON RAIL ASSEMBLY
A


8. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the EGR valve position sensor connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D98-97 (VCVL) - Body ground
    Always
    10 kΩ or higher
    D98-75 (VC) - Body ground
    Always
    10 kΩ or higher
    D98-93 (VCPM) - Body ground
    Always
    10 kΩ or higher
    D98-69 (VCM) - Body ground
    Always
    10 kΩ or higher
    D98-68 (VCS) - Body ground
    Always
    10 kΩ or higher
    B72-55 (VCPA) - Body ground
    Always
    10 kΩ or higher
    B72-57 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the EGR valve position sensor connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Power Source Circuit (from Jan 2017)VC Output Circuit (Jan 2015 – Nov 2015) →