VC Output Circuit
Circuit diagnosis · Vehicles built Dec 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the throttle position sensor (throttle body assembly), EGR valve position sensor (electric EGR control valve assembly), manifold absolute pressure sensor, accelerator pedal position sensor (accelerator pedal rod assembly) and fuel pressure sensor.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.
- OK:
- MIL lights up
|
|
||||
| NG | |
| 2. CHECK CONNECTION BETWEEN GTS AND ECM |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and the GTS on.
Check the communication between the GTS and ECM.
Result Result
Proceed to
Communication is not possible
A
Communication is possible
B
|
|
||||
| A | |
| 3. CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
Reconnect the throttle position sensor connector.
|
|
||||
| A | |
| 4. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
Reconnect the manifold absolute pressure sensor connector.
|
|
||||
| A | |
| 5. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
Reconnect the accelerator position sensor connector.
|
|
||||
| A | |
| 6. CHECK MIL (EGR VALVE POSITION SENSOR) |
Disconnect the EGR valve position sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
Reconnect the EGR valve position sensor connector.
|
|
||||
| A | |
| 7. CHECK MIL (FUEL PRESSURE SENSOR) |
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Check the MIL.
Result Result
Proceed to
MIL does not illuminate
A
MIL illuminates
B
Reconnect the fuel pressure sensor connector.
|
|
||||
| A | |
| 8. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
Disconnect the throttle position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the EGR valve position sensor connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
D98-97 (VCVL) - Body ground
Always
10 kΩ or higher
D98-75 (VC) - Body ground
Always
10 kΩ or higher
D98-93 (VCPM) - Body ground
Always
10 kΩ or higher
D98-69 (VCM) - Body ground
Always
10 kΩ or higher
D98-68 (VCS) - Body ground
Always
10 kΩ or higher
B72-55 (VCPA) - Body ground
Always
10 kΩ or higher
B72-57 (VCP2) - Body ground
Always
10 kΩ or higher
Reconnect the throttle position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the EGR valve position sensor connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connectors.
|
|
||||
| OK | ||
| ||
