2014-2019 Hiace · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jan 2015

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015


CHECK TRANSPONDER KEY ECU ASSEMBLY
B271269E09
  1. Disconnect the H60 transponder key ECU assembly connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H60-1 (+B) - H60-5 (GND)
    Input
    W - W-B
    Battery
    Always
    11 to 14 V
    +B
    H60-2 (IG) - H60-5 (GND)
    Input
    B - W-B
    Ignition switch signal
    Ignition switch off
    Below 1 V
    IG SW
    Ignition switch ON
    11 to 14 V
    H60-3 (KSW) - H60-5 (GND)
    Input
    Y - W-B
    Unlock warning switch signal
    No key in ignition key cylinder
    10 kΩ or higher
    Key SW/B2780
    Key in ignition key cylinder
    Below 1 Ω
    H60-5 (GND) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    H60-7 (CTY) - Body ground
    Input
    G - Body ground
    Door courtesy switch (for driver side) signal
    Driver side door closed
    10 kΩ or higher
    -
    Driver side door open
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the H60 transponder key ECU assembly connector.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    H60-8 (IND) - H60-5 (GND)
    Output
    R - W-B
    Security indicator signal
    No key in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set)
    Pulse generation
    Immobiliser
    Key in ignition key cylinder (immobiliser system unset)
    Below 1 V
    H60-9 (D) - H60-5 (GND)
    Input/Output
    W - W-B
    DLC3 communication
    Without communication
    Below 1 V
    -
    During communication
    Pulse generation
    H60-4 (ANT1) - H60-5 (GND)
    Input/Output
    Y - W-B
    Transponder key amplifier power source
    No key in ignition key cylinder
    4 to 6 V
    -
    Within 3 seconds of inserting key into ignition key cylinder
    Pulse generation
    (See waveform 1)
    H60-15 (ANT2) - H60-5 (GND)
    Input/Output
    L - W-B
    Transponder key amplifier communication signal
    No key in ignition key cylinder
    4 to 6 V
    -
    Within 3 seconds of inserting key into ignition key cylinder
    Pulse generation
    (See waveform 2)
    H60-12 (EFII) - H60-5 (GND)
    Output
    R - W-B
    ECM input signal
    Ignition switch off
    11 to 14 V
    -
    H60-12 (EFII) - H60-5 (GND)
    Output
    R - W-B
    ECM input signal
    Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
    Pulse generation
    (See waveform 3)
    -
    H60-13 (EFIO) - H60-5 (GND)
    Input
    B - W-B
    ECM output signal
    Ignition switch off
    Below 1 V
    -
    Ignition switch ON
    Pulse generation
    (See waveform 4)
    If the result is not as specified, the transponder key ECU assembly may be malfunctioning.

  5. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B329909E01

      Tester Connection
      H60-4 (ANT1) - H60-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting key into ignition key cylinder

    2. Waveform 2 (Reference)
      B329910E01

      Tester Connection
      H60-15 (ANT2) - H60-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of inserting key into ignition key cylinder

    3. Waveform 3 (Reference)
      B325134E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      H60-12 (EFII) - H60-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    4. Waveform 4 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      H60-13 (EFIO) - H60-5 (GND)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 2TR-FE [w/o Dual VVT-i])
B366723E01
Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D97-105 (E1) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D97-46 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D97-45 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
B71-20 (BATT) - D97-105 (E1)
Input
W - W-B
+B power supply
Always
11 to 14 V
-
B71-2 (+B) - D97-105 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B71-10 (IMO) - D97-105 (E1)
Input
R - W-B
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
B71-11 (IMI) - D97-105 (E1)
Output
B - W-B
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-

  1. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B333258E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B71-10 (IMO) - D97-105 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    2. Waveform 2 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B71-11 (IMI) - D97-105 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 1TR-FE [w/ Dual VVT-i], 2TR-FE [w/ Dual VVT-i])
B400832E01
Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D116-59 (E1) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D116-57 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D116-58 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
B94-1 (BATT) - D116-59 (E1)
Input
W - W-B
+B power supply
Always
11 to 14 V
-
B94-3 (+B2) - D116-59 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B94-2 (+B) - D116-59 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B94-45 (IMO) - D116-59 (E1)
Input
R - W-B
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
B94-28 (IMI) - D116-59 (E1)
Output
B - W-B
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-

  1. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B333258E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B94-45 (IMO) - D116-59 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    2. Waveform 2 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B94-28 (IMI) - D116-59 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 1KD-FTV [w/o DPF])
B366723E02
Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D98-109 (E1) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D98-45 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D98-44 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
B72-2 (BATT) - D98-109 (E1)
Input
W - W-B
+B power supply
Always
11 to 14 V
-
B72-20 (+B2) - D98-109 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B72-1 (+B) - D98-109 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B72-15 (IMO) - D98-109 (E1)
Input
R - W-B
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
B72-16 (IMI) - D98-109 (E1)
Output
B - W-B
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-

  1. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B333258E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B72-15 (IMO) - D98-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    2. Waveform 2 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B72-16 (IMI) - D98-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 1KD-FTV [w/ DPF])
B366723E03
Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D99-109 (E1) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D99-45 (E01) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
D99-44 (E02) - Body ground
-
W-B - Body ground
Ground
Always
Below 1 Ω
-
B73-2 (BATT) - D99-109 (E1)
Input
W - W-B
+B power supply
Always
11 to 14 V
-
B73-20 (+B2) - D99-109 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B73-1 (+B) - D99-109 (E1)
Input
L - W-B
+B power supply
Ignition switch ON
11 to 14 V
-
B73-15 (IMO) - D99-109 (E1)
Input
R - W-B
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
B73-16 (IMI) - D99-109 (E1)
Output
B - W-B
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-

  1. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B333258E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B73-15 (IMO) - D99-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    2. Waveform 2 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B73-16 (IMI) - D99-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON


CHECK ECM (for 2KD-FTV)
B366723E04
Tester Connection
Input/Output
Wiring Color
Terminal Description
Condition
Specified Condition
Related Data List Item
D105-109 (E1) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
D105-45 (E01) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
D105-44 (E02) - Body ground
-
BR - Body ground
Ground
Always
Below 1 Ω
-
B88-2 (BATT) - D105-109 (E1)
Input
W - BR
+B power supply
Always
11 to 14 V
-
B88-1 (+B) - D105-109 (E1)
Input
L - BR
+B power supply
Ignition switch ON
11 to 14 V
-
B88-15 (IMO) - D105-109 (E1)
Input
R - BR
Transponder key ECU assembly communication input
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal
Pulse generation
(See waveform 1)
-
B88-16 (IMI) - D105-109 (E1)
Output
B - BR
Transponder key ECU assembly communication output
Ignition switch off
Below 1 V
-
Ignition switch ON
Pulse generation
(See waveform 2)
-

  1. Using an oscilloscope, check the waveform.

    1. Waveform 1 (Reference)
      B333258E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B88-15 (IMO) - D105-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal

    2. Waveform 2 (Reference)
      B333259E02

      Text in Illustration 
      *a
      Approximately 160 ms
      *b
      Approximately 270 ms
      Tester Connection
      B88-16 (IMI) - D105-109 (E1)
      Tool Setting
      2 V/DIV., 500 ms./DIV.
      Condition
      Ignition switch ON

← TERMINALS OF ECU (Oct 2014 – Dec 2014)DIAGNOSIS SYSTEM (Oct 2014 – Dec 2016) →