2014-2019 Hiace · Service Manual SECURITIES

Key Cannot be Registered

Circuit diagnosis · Vehicles built from Oct 2014

DESCRIPTION

A maximum of 5 master key ID codes and 3 sub key ID codes can be registered.

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly is replaced, refer to Service Bulletin.
  1. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


1. CHECK REGISTRATION MODE
  1. Check that the system enters registration mode.

    OK:
    System enters registration mode.



NG
Go to step 5
OK


2. CHECK SECURITY INDICATOR LIGHT OPERATION

  1. In registration mode, insert the key into the ignition key cylinder and check the security indicator light.

    HINT:
    If the new key ID code registration fails, code 2-1 will be output through the security light. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key ID codes exceeds the maximum limit, code 2-3 will be output through the security indicator light. The output details are shown in the following illustration.

    B111593E42
    Text in Illustration 
    *1
    Security Indicator Light
    *2
    Normal (Immobiliser system is operating normally)
    *3
    Code 2-1
    *4
    Code 2-2
    *5
    Code 2-3
    -
    -
    Result 
    Result
    Proceed to
    Code 2-1 or code 2-3 is output
    A
    Code 2-2 is output
    B



B
END (REGISTERED KEY WAS USED)
A


3. READ VALUE USING GTS (TRANSPONDER S-CODE, TRANSPONDER M-CODE)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Immobiliser / Data List.

  1. Read the Data List according to the display on the GTS.

    Immobiliser 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Transponder S-code
    Number of registered sub key / min. 0, max. 15
    Number of registered sub key
    -
    Transponder M-code
    Number of registered master key / min. 0, max. 15
    Number of registered master key
    -
    Result 
    Result
    Proceed to
    5 is displayed for "Transponder M-code" and 0 is displayed for "Transponder S-code"
    A
    0 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code"
    B
    5 is displayed for "Transponder M-code" and 3 is displayed for "Transponder S-code"
    C
    Values are other than above
    D



B
KEY REGISTRATION (MASTER KEY)

C
MAXIMUM NUMBER OF KEYS ALREADY REGISTERED

D
Go to step 4
A

KEY REGISTRATION (SUB-KEY)

4. KEY REGISTRATION
  1. Refer to the table below to determine if additional keys can be registered.

    Number of Keys Registered (Master and Sub)
    Proceed to
    0
    New key ID code registration
    1 to 7
    Additional key ID code registration

  1. Check if an additional key can be registered.

    OK:
    Additional key can be registered.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (KEY MALFUNCTION)

5. INSPECT UNLOCK WARNING SWITCH ASSEMBLY
  1. Remove the unlock warning switch assembly.

  1. Inspect the unlock warning switch assembly (Click here).



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY
OK


6. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)
  1. Disconnect the H26*1 or H27*2 unlock warning switch assembly connector.

  1. Disconnect the H60 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission

    Standard Resistance:
    for Automatic Transmission 
    Tester Connection
    Condition
    Specified Condition
    H26-2 - H60-3 (KSW)
    Always
    Below 1 Ω
    H26-1 - Body ground
    Always
    Below 1 Ω
    H26-2 - Body ground
    Always
    10 kΩ or higher
    H60-3 (KSW) - Body ground
    Always
    10 kΩ or higher
    for Manual Transmission 
    Tester Connection
    Condition
    Specified Condition
    H27-2 - H60-3 (KSW)
    Always
    Below 1 Ω
    H27-1 - Body ground
    Always
    Below 1 Ω
    H27-2 - Body ground
    Always
    10 kΩ or higher
    H60-3 (KSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY


← Engine does not Start but Initial Combustion Occurs (from Dec 2017)Security Indicator Light Does not Blink (Oct 2014 – Mar 2016) →