2014-2019 Hiace · Service Manual SECURITIES

B2796 No Communication in Immobiliser System

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 from Jan 2015

DESCRIPTION

This DTC is stored when a key is inserted into the ignition key cylinder but no communication occurs between the key and transponder key ECU assembly.
DTC No.
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2796
The key ID code cannot be transmitted to the transponder key ECU assembly (1 trip detection logic*).
  1. Key
  2. Harness or connector
  3. Transponder key coil
    Transponder key ECU assembly
Insert the key into the ignition key cylinder
*: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-
Related Data List and Active Test 
DTC No.
Data List and Active Test
B2796
-

WIRING DIAGRAM

B329324E02

INSPECTION PROCEDURE

NOTICE:
  1. If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.
  2. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
  3. When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Insert and remove each registered key one at a time, and check for DTCs each time (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2796 is not output.

    Result 
    Result
    Proceed to
    DTC B2796 is not output
    A
    DTC B2796 is output for all of the keys
    B
    DTC B2796 is output for any of the keys
    C



B
Go to step 3

C
Go to step 6
A

USE SIMULATION METHOD TO CHECK (Click here)

3. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly with a new one.

    HINT:
    Refer to Service Bulletin.

    NOTICE:
    Key ID code registration is necessary when replacing the transponder key ECU assembly.
    Refer to Service Bulletin.


NEXT


4. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


5. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2796 is not output.



NG
REPLACE KEY FOR WHICH DTC WAS OUTPUT
OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

6. REPLACE KEY
  1. Replace the key for which the DTC was stored.

    NOTICE:
    Key ID code registration is necessary when replacing the key.
    Refer to Service Bulletin.


NEXT


7. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


8. CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B2796 is not output.

    Result 
    Result
    Proceed to
    B2796 is not output
    A
    B2796 is output
    B



B
REPLACE TRANSPONDER KEY ECU ASSEMBLY
A

END (KEY WAS DEFECTIVE)


← B2795 Unmatched Key Code (from Jan 2015)B2796 No Communication in Immobiliser System (from Jan 2015) →