DATA LIST / ACTIVE TEST
System information · Vehicles built from Oct 2014
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser or Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
Immobiliser Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Driver side courtesy switch signal / ON or OFF
ON: Driver side door open
OFF: Driver side door closed
-
Key SW
Unlock warning switch signal / ON or OFF
ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-
IG SW
Ignition switch signal / ON or OFF
ON: Ignition switch ON or engine started
OFF: Ignition switch ACC or off
-
Immobiliser
Immobiliser system status / Set or Unset
Set: No key in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to ACC or off
Unset: Key in ignition key cylinder
-
Response
Transponder chip data / NG or OK
NG: Data error
OK: Data OK
-
Frame Error
Transponder chip data / NG or OK
NG: Data error
OK: Data OK
-
Different Serial Number
Transponder chip data / NG or OK
NG: Data error
OK: Data OK
-
Different Encrypt Code
Transponder chip data / NG or OK
NG: Data error
OK: Data OK
-
Abnormal Status
Transponder chip data / NG or OK
NG: Data error
OK: Data OK
-
Bcc Malfunction
Transponder chip data / NG or OK
NG: Incorrect data being sent
OK: Correct data being sent
-
Sub Key
Sub key ID code signal / Reg or Unreg
Reg: Registered sub key ID code sent
Unreg: Unmatching sub key ID code sent
-
Master Key
Master key ID code signal / Reg or Unreg
Reg: Registered master key ID code sent
Unreg: Unmatching master key ID code sent
-
Transponder S-Code
Number of registered sub key / min. 0, max. 15
Number of registered sub key
-
Transponder M-Code
Number of registered master key / min. 0, max. 15
Number of registered master key
-
Reg Code Space Full
Memory space for key codes registration / NOT FULL or FULL
NOT FULL: Key code registration possible
FULL: Key code registration not possible
-
+B
Power source / Break or Normal
Break: Power source open
Normal: Power source normal
-
Antenna Coil Status
Transponder key coil condition / Normal or Fail
Normal: Antenna coil normal
Fail: Antenna coil malfunctioning
-
EEPROM Status
EEPROM status / NG or OK
NG: EEPROM malfunctioning
OK: EEPROM normal
-
E/G Start Permission
Engine start permission / NG or OK
NG: Engine start not permitted
OK: Engine start permitted
-
Immobi ECU Comm Spd
Immobiliser ECU communication speed / Unknown, 50bps, 200bps or No Res
Unknown: ECU communication speed unknown
50bps: ECU communication speed 50 bps
200bps: ECU communication speed 200 bps
No Res: No ECU communication response
-
The Number of DTCs
Number of DTCs / Min.: 0, Max.: 255
Number of stored DTCs
-
- HINT:
- Data from an actual vehicle provided for reference.
-


- *1: Insert a key into the ignition key cylinder and turn the ignition switch to ACC.
- *2: Turn the ignition switch to ON.
- *3: Turn the ignition switch off and remove the key from the ignition key cylinder.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Immobiliser Fuel Cut
Status of immobiliser system fuel cut / ON or OFF
ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser / Active Test.
Perform the Active Test according to the display on the GTS.
Immobiliser Tester Display
Test Part
Control Range
Diagnostic Note
Security Indicator
Security indicator light
ON/OFF
-