2014-2019 Hiace · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Oct 2014


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the surface of the commutator for dirt and burns.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
    If necessary, replace the starter armature assembly.

  1. Inspect the commutator for an open circuit.

    1. A122065E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. Inspect the commutator for a short circuit.

    1. A122066E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Coil core - Segment
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Segment
      *b
      Coil Core
      If the result is not as specified, replace the starter armature assembly.

  1. A122067
    Check the commutator circle runout.

    1. Place the armature shaft on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum circle runout:
      0.05 mm (0.00197 in.)

      If the circle runout is more than the maximum, replace the starter armature assembly.

  1. Check the commutator diameter.

    1. A122068
      Using a vernier caliper, measure the commutator diameter.

      Standard diameter:
      28 mm (1.10 in.)

      Minimum diameter:
      27 mm (1.06 in.)

      If the diameter is less than the minimum, replace the starter armature assembly.

  1. Check the undercut depth.

    1. A122069
      Using a vernier caliper, measure the undercut depth of the commutator.

      Standard depth:
      0.6 mm (0.0236 in.)

      Minimum depth:
      0.2 mm (0.00787 in.)

      If the undercut depth is less than the minimum, replace the starter armature assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. A122070
    Inspect for an open circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Lead wire - Field coil brush lead
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. A122071
    Inspect for a short circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Starter yoke body - Field coil brush lead
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter yoke assembly.


INSPECT BRUSH LENGTH

  1. A122072
    Inspect the brush length.

    1. Using a vernier caliper, measure the brush length.

      Standard brush length:
      14.0 mm (0.551 in.)

      Minimum brush length:
      9.0 mm (0.354 in.)

      If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Inspect the brush insulation.

    1. A122074E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush holder - Negative (-) brush holder
      Always
      10 kΩ or higher

      Text in Illustration 
      *a
      Positive (+) brush holder
      *b
      Negative (-) brush holder
      If the result is not as specified, replace the starter brush holder assembly.

  1. A122073
    Check the brush spring load.

    1. Take a pull scale reading the instant the brush spring separates from the brush.

      Standard spring load:
      14 to 18 N (1.4 to 1.8 kgf, 3.1 to 4.0 lbf)

      Minimum spring load:
      8.8 N (0.9 kgf, 2.0 lbf)

      If the spring load is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Check the gear teeth on the planetary gears, and the internal gear and pinion gear of the starter center bearing clutch sub-assembly for wear or damage.
    If a planetary gear or the internal gear is damaged, replace the starter center bearing clutch sub-assembly.
    If the starter clutch pinion gear teeth are damaged, replace the starter center bearing clutch sub-assembly and also inspect the flywheel ring gear for wear or damage.

  1. A258152
    Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter center bearing clutch sub-assembly.

  1. Turn the pinion gear by hand while applying inward force and check the movement of the bearing.
    If resistance is felt or the bearing sticks, replace the starter center bearing clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. Inspect the plunger.

    1. A122076
      Push in the plunger and check that it returns quickly to its original position.

      NOTICE:
      To avoid damaging the inside of the magnet starter switch assembly, do not release the plunger quickly.

      If the result is not as specified, replace the magnet starter switch assembly.

  1. Check the pull-in coil for an open circuit.

    1. A122077E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal C - Terminal 50
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Terminal C
      *b
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

  1. Check the holding coil for an open circuit.

    1. A122078E05
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *a
      Switch Body
      *b
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Oct 2014)REASSEMBLY (from Oct 2014) →