2014-2019 Hiace · Service Manual ENGINE

U0101 Lost Communication with TCM

Diagnostic trouble codes · Vehicles built Oct 2014 – Dec 2014

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

The ECM intercommunicates with the TCM through the Controller Area Network (CAN).
If there is a problem in this intercommunication, the ECM sets the DTC.
DTC No.
DTC Detection Condition
Trouble Area
U0101
  1. Following conditions are met for 1.25 seconds (1 trip detection logic):
    1. Ignition switch ON
    2. Battery voltage 10.5 V or more
    3. No intercommunication between ECM and TCM
  1. ECM
  2. TCM
  3. ECM to TCM circuit

WIRING DIAGRAM

A319079E03

INSPECTION PROCEDURE


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    U0101 is output
    A
    U0101 and other DTCs are output
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART
A


2. INSPECT TCM

  1. C216560E30
    Disconnect the TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    O3-5 (BATT) - O1-1 (E1)
    Ignition switch ON
    11 to 14 V

  1. Reconnect the TCM connector.

Text in Illustration 
*a
Rear view of wire harness connector
(to TCM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (TCM - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D98-40 (CAN+) - O3-21 (CAN+)
    Always
    Below 1 Ω
    D98-63 (CAN-) - O3-20 (CAN-)
    Always
    Below 1 Ω
    D98-40 (CAN+) or O3-21 (CAN+) - Body ground
    Always
    10 kΩ or higher
    D98-63 (CAN-) or O3-20 (CAN-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the TCM connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    U0101 is output
    B



B
REPLACE TCM
A

END


← P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low (+ P2565) (from Jan 2017)U0101 Lost Communication with TCM (Jan 2015 – Nov 2015) →