Unable to Unlock Steering Wheel (Engine cannot Start)
Circuit diagnosis · Vehicles built Jan 2015 – Mar 2016
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.
| Problem Symptom |
Data List Item |
Active Test Item |
| Unable to unlock steering wheel (Engine cannot start) |
Entry&Start
|
- |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Perform either of the following operations to lock/unlock the steering:
- To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
- To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
- The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
- After performing repairs, confirm that the problem does not occur.
- Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (Refer to the Service Bulletin).
- If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.
- When starting the engine, make sure that the shift lever is in P and that the shift lever is not tilted.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. CHECK ENGINE SWITCH (SWITCH CONDITION) |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:
- OK:
- Off → on (ACC) → on (IG) → off
Result Result
Proceed to
OK
Smart warning light indicator type
A
Multi-information display type
B
NG
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK SMART WARNING LIGHT INDICATOR |
Turn the engine switch on (IG).
Check that the smart warning light indicator on the combination meter assembly is rapidly blinking green.
Result Result
Proceed to
Smart warning light indicator is blinking rapidly
A
Smart warning light indicator is not blinking rapidly
B
|
|
||||
| A | |
| 3. CHECK STEERING UNLOCK |
While turning the steering wheel left and right, press the engine switch.
Check that the steering is unlocked.
- OK:
- The steering is unlocked.
|
|
||||
| OK | ||
| ||
| 4. CHECK INDICATOR |
With the engine switch on (IG), check that the smart warning light indicator on the combination meter assembly is rapidly blinking green and "STEERING LOCK ACTIVE" message is displayed on the multi-information display in the combination meter assembly.
Result Result
Proceed to
Smart warning light indicator on the combination meter assembly is rapidly blinking green and "STEERING LOCK ACTIVE" message is displayed
A
Smart warning light indicator on the combination meter assembly is not rapidly blinking green and "STEERING LOCK ACTIVE" message is not displayed
B
|
|
||||
| OK | |
| 5. CHECK STEERING UNLOCK |
While turning the steering wheel left and right, press the engine switch.
Check that the steering is unlocked.
- OK:
- The steering is unlocked.
|
|
||||
| OK | ||
| ||
| 6. CHECK DTC (ALL) |
Using the GTS, confirm the output of DTCs for all systems.
- OK:
- No DTCs are output.
- CAUTION:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
|
|
||||
| OK | |
| 7. READ VALUE USING GTS (UNLOCK REQUEST RECEIVE) |
Use the Data List to check if the steering lock request is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Unlock Request Receive
Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG - HINT:
- The reception state is maintained for 10 seconds.
- When 10 seconds or more elapse after receiving the signal, the item changes to "NG".
- The reception state is maintained for 10 seconds.
OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above
- If the unlock signal has not been received, the engine cannot be started.
- If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
- OK:
- Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.
Measure the resistance and voltage according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
H80-1 (GND) - Body ground
Always
Below 1 Ω
- NOTICE:
- If the result is not as specified, check for looseness in the connection which leads to ground.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
H80-7 (B) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly))
|
|
||||
| OK | |
| 9. INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL) |
Reconnect the H80 steering lock ECU (steering lock actuator assembly) connector.
Check the signal waveform according to the condition(s) in the table below.

Standard Frequency Item
Content
Tester Connection
H80-3 (IGE) - H80-1 (GND)
Tool Setting
2 V/DIV., 200 ms./DIV.
Vehicle Condition
Steering lock motor not operating → Operating → Not operating
Text in Illustration *a
Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
*b
Steering lock motor not operating
*c
Steering lock motor operating
- HINT:
- When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
- In order to take measurements when the lock motor is operating, perform either of the following operations:
- To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
- To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
- When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
- OK:
- There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H80-3 (IGE) - B75-17 (SLR+)
Always
Below 1 Ω
H80-3 (IGE) - Body ground
10 kΩ or higher
B75-17 (SLR+) - Body ground
|
|
||||
| OK | |
| 11. INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
Reconnect the H80 steering lock ECU (steering lock actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
H80-3 (IGE) - Body ground
Always
11 to 14 V
Text in Illustration *a
Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))
|
|
||||
| OK | ||
| ||
| 12. READ VALUE USING GTS (S CODE CHECK) |
Use the Data List to check if S code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Check
Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
OK: Verification result normal
NG: Verification result abnormal
When NG is displayed: - The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- The steering cannot be locked.
- The steering cannot be unlocked (the engine cannot be started).
- OK:
- OK is displayed on the GTS.
- HINT:
- Reasons for verification failure:
- The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- There is a problem with the communication between ECUs.
- An ECU is replaced, but is not registered.
- An ECU is replaced with an ECU which has a code already stored in it.
- The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
|
|
||||
| OK | |
| 13. READ VALUE USING GTS (L CODE CHECK) |
Use the Data List to check if L code certification is functioning properly.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Check
Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly) / OK or NG
OK: Verification result normal
NG: Verification result abnormal
When NG is displayed: - The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.
- The steering cannot be locked.
- The steering cannot be unlocked (the engine cannot be started).
- OK:
- OK is displayed on the GTS.
- HINT:
- Reasons for verification failure:
- The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- There is a problem with the communication between ECUs.
- An ECU is replaced, but is not registered.
- An ECU is replaced with an ECU which has a code already stored in it.
- The steering lock ECU (steering lock actuator assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.
|
|
||||
| OK | |
| 14. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform registration procedures (Refer to the Service Bulletin).
Turn the engine switch on (IG).
Turn the steering wheel and check the steering condition.
- OK:
- Steering is unlocked.
|
|
||||
| OK | ||
| ||
| 15. REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).
Perform registration procedures (Refer to the Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Check
Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
OK: Verification result normal
NG: Verification result abnormal
When NG is displayed: - The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
- The steering cannot be locked.
- The steering cannot be unlocked (the engine cannot be started).
- OK:
- OK is displayed on the GTS.
- The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
|
|
||||
| OK | ||
| ||
| 16. REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) |
Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).
Perform registration procedures (Refer to the Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
Entry&Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Check
Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator assembly) / OK or NG
OK: Verification result normal
NG: Verification result abnormal
When a malfunction is present: - The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.
- The steering cannot be locked.
- The steering cannot be unlocked (the engine cannot be started).
- OK:
- OK is displayed on the GTS.
- The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is not registered or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator assembly) is malfunctioning.
|
|
||||
| OK | ||
| ||
