Immobiliser System does not Operate Properly
Circuit diagnosis · Vehicles built Jan 2015 – Nov 2015
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Nov 2015 Dec 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
- The engine immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly. The system unsets if these ID codes match. Thus, the ID code box (immobiliser code ECU) and the ECM communicate with each other enabling the engine to start.
WIRING DIAGRAM
Click hereINSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The engine immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly (Click here).
- Before replacing the ID code box (immobiliser code ECU), refer to Service Bulletin.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation (Click here)."
- When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. CHECK FOR DTC |
Check for DTCs (Click here).
Result: Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 2. READ VALUE USING GTS (IMMOBILISER FUEL CUT) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Read the Data List according to the display on the GTS.
| Tester Display |
Measurement Item |
Normal Condition |
Reference Value |
Diagnostic Note |
| Immobiliser Fuel Cut |
Immobiliser fuel cut status |
ON or OFF |
ON: Immobiliser fuel cut on OFF: Immobiliser fuel cut off |
- |
- OK:
- The item in the Data List indicates "OFF".
|
|
||||
| OK | ||
| ||
| 3. CHECK WHETHER ENGINE STARTS |
Check that the engine starts 5 seconds after the engine switch is turned on (IG).
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
| 4. REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| Go to step 6 |
| 5. CHECK WHETHER ENGINE STARTS |
Check that the engine starts 5 seconds after the engine switch is turned on (IG).
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
| 6. REPLACE ECM |
Temporarily replace the ECM with a new or known good one (Click here).
| NEXT | |
| 7. CHECK WHETHER ENGINE STARTS |
Check that the engine starts 5 seconds after the engine switch is turned on (IG).
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR (ID CODE BOX [IMMOBILISER CODE ECU] - ECM) |
Disconnect the H81 ID code box (immobiliser code ECU) connector.
Disconnect the B72 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
H81-3 (EFII) - B72-15 (IMO)
Always
Below 1 Ω
H81-3 (EFII) - Body ground
Always
10 kΩ or higher
B72-15 (IMO) - Body ground
Always
10 kΩ or higher
H81-4 (EFIO) - B72-16 (IMI)
Always
Below 1 Ω
H81-4 (EFIO) - Body ground
Always
10 kΩ or higher
B72-16 (IMI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 9. REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
Replace the ID code box (immobiliser code ECU) with a new one.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| 10. REGISTER RECOGNITION CODES |
Register the recognition codes in the ECUs.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| 11. REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
- HINT:
- Refer to Service Bulletin.
| NEXT | |
| 12. CHECK WHETHER ENGINE STARTS |
Check that the engine starts 5 seconds after the engine switch is turned on (IG).
- OK:
- Engine starts normally.
|
|
||||
| OK | ||
| ||
