2014-2019 Hiace · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Oct 2014 – Mar 2016

Versions by build date: Oct 2014 – Mar 2016 from Apr 2016


1. INSTALL NO. 2 COOLING FAN MOTOR (w/ Air Conditioning System)
  1. Install the No. 2 cooling fan motor with the 5 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 34 in.*lbf }


2. INSTALL NO. 1 COOLING FAN MOTOR
  1. Install the No. 1 cooling fan motor with the 5 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 34 in.*lbf }


3. INSTALL NO. 2 FAN (w/ Air Conditioning System)
  1. Install the No. 2 fan with the 3 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 34 in.*lbf }


4. INSTALL NO. 1 FAN
  1. Install the No. 1 fan with the 3 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 34 in.*lbf }


5. INSTALL FAN SHROUD
  1. Install the fan shroud with the 6 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    Do not drop the radiator assembly.

  1. w/o Air Conditioning System:
    Attach the 3 clamps and connect the connector.

  1. w/ Air Conditioning System:
    Attach the 2 clamps and connect the 2 connectors.


6. INSTALL FAN BRACKET SUB-ASSEMBLY
  1. Install the fan bracket sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Attach the clamp.

  1. w/ DPF:
    Connect the 4 connectors to the injector driver.


7. CONNECT OIL COOLER TUBE (for Automatic Transmission)
  1. Connect the 2 oil cooler hoses to the 2 oil cooler tubes, and slide the 2 hose clamps to secure the hoses.

  1. Attach the 2 oil cooler tube clamps.


8. INSPECT AUTOMATIC TRANSMISSION FLUID LEVEL (for Automatic Transmission)

HINT:
Drive the vehicle so that the engine and transmission are at normal operating temperature.

Fluid temperature:
70 to 80 °C (158 to 176 °F)

  1. D025120E01
    Park the vehicle on a level surface and set the parking brake.

  1. With the engine idling and the brake pedal depressed, move shift the lever into all positions from P to L and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put it back all the way.

  1. Take it out again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.


9. INSPECT FOR FLUID LEAK (for Automatic Transmission)

10. INSTALL NO. 1 ENGINE UNDER COVER (for Cold Area Specification Vehicles)
  1. Install the No. 1 engine under cover with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

← REMOVAL (from Apr 2016)INSTALLATION (from Apr 2016) →