Power Source Mode does not Change to ON (IG)
Circuit diagnosis · Vehicles built Oct 2014 – Dec 2014
Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017
DESCRIPTION
If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.- HINT:
- When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| Problem Symptom |
Data List Item |
Active Test Item |
| Power source mode does not change to on (IG) but does change to on (ACC) |
Power Source Control
|
- |
WIRING DIAGRAM
Refer to DTC B2271 (Click here)INSPECTION PROCEDURE
- NOTICE:
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
- The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
- Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
- If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
- Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or main body ECU (multiplex network body ECU), refer to the smart entry and start system (for Start Function) precaution (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After completing repairs, confirm that the problem does not occur.
- When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
| 1. CHECK FOR DTC |
Using the GTS, check for certification ECU (smart key ECU assembly) DTCs (Click here).
- Result:
Result
Proceed to
DTCs are not output.
A
Smart entry and start system (for Start Function) DTCs are output
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 RELAY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Remove the IG1 relay from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - 1 (IG1 relay)
Always
Below 1 Ω
2 (IG1 relay) - Body ground
B75-20 (IG1D) or 1 (IG1 relay) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT IG1 RELAY |
Remove the IG1 relay from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY) |
Disconnect the B75 certification ECU (smart key ECU assembly) connector.
Disconnect the 12D and 12E No. 2 integration relay connectors.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - 12D-2
Always
Below 1 Ω
12E-4 - Body ground
B75-20 (IG1D) or 12D-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT NO. 2 INTEGRATION RELAY |
Remove the No. 2 integration relay.
Measure the resistance according to the value(s) in the table below.


| *a |
Component without harness connected (No. 2 Integration Relay) |
- |
- |
- Standard Resistance:
Tester Connection
Condition
Specified Condition
12A-1 - 12D- 8
Battery voltage not applied to terminals 12D-2 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12D-2 and 12E-4
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the B75 certification ECU (smart key ECU assembly) connector.
Install the IG1 relay.
Install the No. 2 integration relay.
Measure the resistance according to the value(s) in the table below.


| *a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
- |
- |
- Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - Body ground
Engine switch on (ACC) → Engine switch on (IG)
1 V or less → 9 V or higher
|
|
||||
| OK | ||
| ||
