2014-2019 Hiace · Service Manual ENGINE

Power Source Mode does not Change to ON (IG)

Circuit diagnosis · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Oct 2014 – Dec 2014 Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 Jan 2017 – Nov 2017 from Dec 2017

DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
  1. Power Supply Condition
  2. IG Relay Monitor (Inside)
  3. IG Relay Monitor (Outside)
  4. IG Circuit
-

WIRING DIAGRAM

Refer to DTC B2271 (Click here)

INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
  4. If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or main body ECU (multiplex network body ECU), refer to the smart entry and start system (for Start Function) precaution (Click here).
  6. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  7. After completing repairs, confirm that the problem does not occur.


1. CHECK FOR DTC
  1. Using the GTS, check for certification ECU (smart key ECU assembly) DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs are not output.
    A
    Smart entry and start system (for Start Function) DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG1 RELAY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Remove the IG1 relay from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-20 (IG1D) - 1 (IG1 relay)
    Always
    Below 1 Ω
    2 (IG1 relay) - Body ground
    B75-20 (IG1D) or 1 (IG1 relay) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT IG1 RELAY
  1. Remove the IG1 relay from the instrument panel junction block assembly.

  1. A111813E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE IG1 RELAY
OK


4. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INTEGRATION RELAY)
  1. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the 12D and 12E No. 2 integration relay connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B75-20 (IG1D) - 12D-2
    Always
    Below 1 Ω
    12E-4 - Body ground
    B75-20 (IG1D) or 12D-2 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT NO. 2 INTEGRATION RELAY
  1. Remove the No. 2 integration relay.

  1. Measure the resistance according to the value(s) in the table below.C302430E02

Text in Illustration 
*a
Component without harness connected
(No. 2 Integration Relay)
-
-

Standard Resistance:
Tester Connection
Condition
Specified Condition
12A-1 - 12D- 8
Battery voltage not applied to terminals 12D-2 and 12E-4
10 kΩ or higher
Battery voltage applied to terminals 12D-2 and 12E-4
Below 1 Ω



NG
REPLACE NO. 2 INTEGRATION RELAY
OK


6. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Reconnect the B75 certification ECU (smart key ECU assembly) connector.

  1. Install the IG1 relay.

  1. Install the No. 2 integration relay.

  1. Measure the resistance according to the value(s) in the table below.

C299852E01
Text in Illustration 
*a
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
-
-

Standard Voltage:
Tester Connection
Condition
Specified Condition
B75-20 (IG1D) - Body ground
Engine switch on (ACC) → Engine switch on (IG)
1 V or less → 9 V or higher



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← Power Source Mode does not Change to ON (IG) (Oct 2014 – Dec 2014)Power Source Mode does not Change to ON (IG) (Apr 2016 – Dec 2016) →