2014-2019 Hiace · Service Manual TRANSMISSION

U0100/A2 Lost Communication with ECM/PCM "A"

Diagnostic trouble codes · Vehicles built from Jan 2017

Versions by build date: Oct 2014 – Dec 2016 from Jan 2017

DESCRIPTION

The TCM communicates with the ECM through the Controller Area Network (CAN). If there is a problem in this communication, the TCM sets the DTC.
DTC No.
DTC Detection Condition
Trouble Area
U0100/A2
When TCM cannot receive communication signals from ECM.
(1 trip detection logic)
  1. Open or short in TCM to ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM

C229408E02

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (TCM - ECM)
  1. Disconnect the TCM connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance.

    Standard Resistance:
    for 1KD-FTV w/ DPF 
    Tester Connection
    Condition
    Specified Condition
    O3-21 (CAN+) - D99-40 (CAN+)
    Always
    Below 1 Ω
    O3-20 (CAN-) - D99-63 (CAN-)
    Always
    Below 1 Ω
    O3-21 (CAN+) or D99-40 (CAN+) - Body ground
    Always
    10 kΩ or higher
    O3-20 (CAN-) or D99-63 (CAN-) - Body ground
    Always
    10 kΩ or higher
    for 1KD-FTV w/o DPF 
    Tester Connection
    Condition
    Specified Condition
    O3-21 (CAN+) - D98-40 (CAN+)
    Always
    Below 1 Ω
    O3-20 (CAN-) - D98-63 (CAN-)
    Always
    Below 1 Ω
    O3-21 (CAN+) or D98-40 (CAN+) - Body ground
    Always
    10 kΩ or higher
    O3-20 (CAN-) or D98-63 (CAN-) - Body ground
    Always
    10 kΩ or higher
    for 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    O3-21 (CAN+) - B88-4 (CAN+)
    Always
    Below 1 Ω
    O3-20 (CAN-) - B88-5 (CAN-)
    Always
    Below 1 Ω
    O3-21 (CAN+) or B88-4 (CAN+) - Body ground
    Always
    10 kΩ or higher
    O3-20 (CAN-) or B88-5 (CAN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE TCM
  1. Replace the TCM.

    NOTICE:
    Replace the TCM with a TCM from a normally functioning vehicle of the same model.


NEXT


3. CHECK DTC OUTPUT (DTC U0100/A2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn on the tester.

  1. Clear the DTC (Click here).

  1. Turn the ignition switch off and turn the tester off.

  1. Start the engine and turn on the tester.

  1. Select the item: "Powertrain / ECT / DTC / Current or Pending".

  1. Read the DTCs using the intelligent tester.

    Result:
    Display (DTC output)
    Proceed to
    U0100/A2
    A
    No DTC
    B

    HINT:
    When not using the intelligent tester, refer to DTC CHECK / CLEAR (Click here).



B
REPLACE TCM
A

REPLACE ECM


← U0100/A2 Lost Communication with ECM/PCM "A" (Oct 2014 – Dec 2016)INSPECTION (from Oct 2014) →