Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM
Diagnosis Circuit
Circuit diagnosis · Vehicles built Apr 2016 – Dec 2016
Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017
DESCRIPTION
DTC output mode is set by connecting terminals TC and CG of the DLC3. DTCs are output by the blinking of the SRS warning light.
HINT:
When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the center airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
After replacing the center airbag sensor assembly, refer to initialization (Click here ).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here ).
1. CHECK CAN COMMUNICATION SYSTEM
Check if a CAN communication system DTC is output.
Result
Result
Proceed to
DTCs are output
A
DTC is not output
B
A
B
2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
Turn the ignition switch off.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for 1KD-FTV (w/ DPF)
Tester Connection
Condition
Specified Condition
B73-26 (TC) - H23-13 (TC)
Always
Below 1 Ω
for 1KD-FTV (w/o DPF)
Tester Connection
Condition
Specified Condition
B72-26 (TC) - H23-13 (TC)
Always
Below 1 Ω
for 2KD-FTV
Tester Connection
Condition
Specified Condition
B88-26 (TC) - H23-13 (TC)
Always
Below 1 Ω
for 1TR-FE, 2TR-FE (w/ Dual VVT-i)
Tester Connection
Condition
Specified Condition
B94-33 (TC) - H23-13 (TC)
Always
Below 1 Ω
for 1TR-FE, 2TR-FE (w/o Dual VVT-i)
Tester Connection
Condition
Specified Condition
B71-41 (TC) - H23-13 (TC)
Always
Below 1 Ω
for 5L-E
Tester Connection
Condition
Specified Condition
B74-40 (TC) - H23-16 (BAT)
Always
Below 1 Ω
Text in Illustration
*A
for 1KD-FTV (w/ DPF)
*B
for 1KD-FTV (w/o DPF)
*C
for 2KD-FTV
*D
for 1TR-FE, 2TR-FE
*E
for 5L-E
*a
Front view of wire harness connector (to ECM)
*b
Front view of DLC3
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
H23-4 (CG) - Body ground
Always
Below 1 Ω
Text in Illustration
*a
Front view of DLC3
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for 1KD-FTV (w/ DPF)
Tester Connection
Condition
Specified Condition
B73-26 (TC) - Body ground
Always
1 MΩ or higher
for 1KD-FTV (w/o DPF)
Tester Connection
Condition
Specified Condition
B12-26 (TC) - Body ground
Always
1 MΩ or higher
for 2KD-FTV
Tester Connection
Condition
Specified Condition
B88-26 (TC) - Body ground
Always
1 MΩ or higher
for 1TR-FE, 2TR-FE (w/ Dual VVT-i)
Tester Connection
Condition
Specified Condition
B94-33 (TC) - Body ground
Always
1 MΩ or higher
for 1TR-FE, 2TR-FE (w/o Dual VVT-i)
Tester Connection
Condition
Specified Condition
B71-41 (TC) - Body ground
Always
1 MΩ or higher
for 5L-E
Tester Connection
Condition
Specified Condition
B74-40 (TC) - Body ground
Always
6 kΩ or higher
Text in Illustration
*A
for 1KD-FTV (w/ DPF)
*B
for 1KD-FTV (w/o DPF)
*C
for 2KD-FTV
*D
for 1TR-FE, 2TR-FE
*E
for 5L-E
*a
Front view of wire harness connector (to ECM)
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU
OK
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here )