2014-2019 Hiace · Service Manual RESTRAINTS

Diagnosis Circuit

Circuit diagnosis · Vehicles built Jan 2015 – Mar 2016

Versions by build date: Jan 2015 – Mar 2016 Apr 2016 – Dec 2016 from Jan 2017

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.
DTCs are output by the blinking of the SRS warning light.

HINT:
  1. When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
  2. A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the center airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.


WIRING DIAGRAM

C323823E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the center airbag sensor assembly, refer to initialization (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output.

    Result 
    Result
    Proceed to
    DTCs are output
    A
    DTC is not output
    B



A
GO TO CAN COMMUNICATION SYSTEM (Click here)
B


2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

  1. Turn the ignition switch off.C317030E03

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Condition
    Specified Condition
    B73-26 (TC) - H23-13 (TC)
    Always
    Below 1 Ω
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Condition
    Specified Condition
    B72-26 (TC) - H23-13 (TC)
    Always
    Below 1 Ω
    for 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    B88-26 (TC) - H23-13 (TC)
    Always
    Below 1 Ω
    for 1TR-FE, 2TR-FE (w/ Dual VVT-i) 
    Tester Connection
    Condition
    Specified Condition
    B94-33 (TC) - H23-13 (TC)
    Always
    Below 1 Ω
    for 1TR-FE, 2TR-FE (w/o Dual VVT-i) 
    Tester Connection
    Condition
    Specified Condition
    B71-41 (TC) - H23-13 (TC)
    Always
    Below 1 Ω
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    B74-40 (TC) - H23-16 (BAT)
    Always
    Below 1 Ω

    Text in Illustration 
    *A
    for 1KD-FTV (w/ DPF)
    *B
    for 1KD-FTV (w/o DPF)
    *C
    for 2KD-FTV
    *D
    for 1TR-FE, 2TR-FE
    *E
    for 5L-E
    *a
    Front view of wire harness connector
    (to ECM)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

  1. C198509E29
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H23-4 (CG) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

  1. C323822E01
    Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1KD-FTV (w/ DPF) 
    Tester Connection
    Condition
    Specified Condition
    B73-26 (TC) - Body ground
    Always
    1 MΩ or higher
    for 1KD-FTV (w/o DPF) 
    Tester Connection
    Condition
    Specified Condition
    B12-26 (TC) - Body ground
    Always
    1 MΩ or higher
    for 2KD-FTV 
    Tester Connection
    Condition
    Specified Condition
    B88-26 (TC) - Body ground
    Always
    1 MΩ or higher
    for 1TR-FE, 2TR-FE (w/ Dual VVT-i) 
    Tester Connection
    Condition
    Specified Condition
    B94-33 (TC) - Body ground
    Always
    1 MΩ or higher
    for 1TR-FE, 2TR-FE (w/o Dual VVT-i) 
    Tester Connection
    Condition
    Specified Condition
    B71-41 (TC) - Body ground
    Always
    1 MΩ or higher
    for 5L-E 
    Tester Connection
    Condition
    Specified Condition
    B74-40 (TC) - Body ground
    Always
    6 kΩ or higher

    Text in Illustration 
    *A
    for 1KD-FTV (w/ DPF)
    *B
    for 1KD-FTV (w/o DPF)
    *C
    for 2KD-FTV
    *D
    for 1TR-FE, 2TR-FE
    *E
    for 5L-E
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← TC and CG Terminal Circuit (Oct 2014 – Dec 2014)Diagnosis Circuit (Apr 2016 – Dec 2016) →